Priming Sample Clauses

Priming. Immediately after surface preparation, apply primer according to manufacturer's written instructions and at rate recommended by SSPC to provide a minimum dry film thickness of 1.5 mils (0.038 mm). Use priming methods that result in full coverage of joints, corners, edges, and exposed surfaces. 1. Stripe paint corners, crevices, bolts, welds, and sharp edges. 2. Apply two coats of shop paint to surfaces that are inaccessible after assembly or erection. Change color of second coat to distinguish it from first.
AutoNDA by SimpleDocs
Priming. .1 Where necessary to prevent staining, mask adjacent surfaces prior to priming and caulking. .2 Prime sides of joints in accordance with sealant manufacturer's instructions immediately prior to caulking.
Priming. All joinery shall be delivered to the site unprimed and shall be primed, (as measured in Painting and Decorating), immediately after inspection and before fixing.
Priming. The pump shall provide the following pump priming options: a guzzler type hand primer or a 12 VDC Electric primer
Priming. Walls need to be primed using your own water-based primer, which will need to dry for at least 2 hours.
Priming. The Contractor will employ an appropriate priming system for each applicable surface on the home. PUTTYING: Windows (if applicable) will be inspected and areas of failing putty will be cleaned, primed if bare wood is showing and re-puttied. CAULKING: Caulking will be done in contractor’s discretion where moisture can enter. EXAMPLES: around windows, doors, and corner moldings. Caulking is not recommended in areas of internal moisture release such as under overhangs, window xxxxx or between overlapping clapboards. MILDEW WASH: Existing mildew growth where evident, will be washed with a TSP (Trisodium Phosphate) solution or similar detergent in contractor’s sole discretion. This process may streak windows. MATERIAL TYPE: The Contractor uses superior performing products for the specific surfaces and conditions of your home. Substitutions of paint type/manufacturer may be made in contractor’s sole discretion. EQUIPMENT STORAGE: The Contractor will maintain a reasonably neat, orderly and safe working environment. At the conclusion of each working day the materials and equipment will be stacked, secured and stored at the job site. TOTAL COAT PEELING: Peeling to the bare wood is usually caused by moisture pushing out from behind the top coat(s). Moisture related peeling is not necessarily related to poor work or product failure. If the source of moisture cannot be indentified and/or eliminated, the coating failure will generally continue to occur. INITIAL OR UNDERLYING COATING FAILURE: This peeling between layers of can paint happen at any time. Scraping to a firm base will help but not prevent this type of failure. To remedy this condition, complete paint removal is required and is very time consuming and expensive. A maintenance painting program is generally required and more cost effective than total paint removal. HOMEOWNER ASSISTANCE: Please be advised, unless noted in writing by the contractor or its representative, you are responsible for the following: removal of aluminum storm window glass and screen inserts; tying back curtains, drapes or other window coverings; sliding windows for 3-5 days upon completion to keep clear and free from sticking; remove personal belongings in or near the areas where we will be working; trim and/or cut back bushes, trees, shrubs, etc. where necessary to allow access to included surfaces. The contractor, its agents and owners are not liable for damages caused due to your failure or inability to provide the above specified as...
Priming since Xxxxxxxx’x model can link structures in memory based on the terms they contain, he is able to predict a positive priming effect. This is an empirical effect where the presentation of an item makes it easier for the subject to retrieve a related item shortly afterwards – e.g. presentation of the word dog might prime the word cat, but not the unrelated word whisky. (This is an effect we will find it harder to predict with the model we put forward, since – in the name of simplicity – we will not be considering links between items in memory.)
AutoNDA by SimpleDocs
Priming. .1 Verify the extent of surfaces primed under Work of other Sections. Include the priming of unprimed surfaces in Work of this Section.

Related to Priming

  • Adequate Protection Each Second-Priority Agent, on behalf of itself and each applicable Second-Priority Secured Party, agrees that none of them shall contest (or support any other Person contesting) (a) any request by the Intercreditor Agent or the Senior Lenders for adequate protection or (b) any objection by the Intercreditor Agent or the Senior Lenders to any motion, relief, action or proceeding based on the Intercreditor Agent’s or the Senior Lenders’ claiming a lack of adequate protection. Notwithstanding the foregoing, in any Insolvency or Liquidation Proceeding, (i) if the Senior Lenders (or any subset thereof) are granted adequate protection in the form of additional collateral in connection with any DIP Financing or use of cash collateral under Section 363 or Section 364 of Title 11 of the United States Code or any similar Bankruptcy Law, then each Second-Priority Agent, on behalf of itself and any applicable Second-Priority Secured Party, may seek or request adequate protection in the form of a replacement Lien on such additional collateral, which Lien is subordinated to the Liens securing the Senior Lender Claims and such DIP Financing (and all Obligations relating thereto) on the same basis as the other Liens securing the Second-Priority Claims are so subordinated to the Liens securing Senior Lender Claims under this Agreement and (ii) in the event any Second-Priority Agent, on behalf of itself or any applicable Second-Priority Secured Party, seeks or requests adequate protection and such adequate protection is granted in the form of additional collateral, then such Second-Priority Agent, on behalf of itself or each such Second-Priority Secured Party, agrees that the Senior-Priority Agents shall also be granted a senior Lien on such additional collateral as security for the applicable Senior Lender Claims and any such DIP Financing and that any Lien on such additional collateral securing the Second-Priority Claims shall be subordinated to the Liens on such collateral securing the Senior Lender Claims and any such DIP Financing (and all Obligations relating thereto) and any other Liens granted to the Senior Lenders as adequate protection on the same basis as the other Liens securing the Second-Priority Claims are so subordinated to such Liens securing Senior Lender Claims under this Agreement.

  • Composition and Priority The Contractor agrees to provide commodities or contractual services to the Customer as specified in the Contract. Additionally, the terms of the Contract supersede the terms of all prior agreements between the Parties on this subject matter.

  • Priority Hiring If the Contract Amount is over $200,000 and this Agreement is for services (other than Consulting Services), this section is applicable. Contractor shall give priority consideration in filling vacancies in positions funded by this Agreement to qualified recipients of aid under Welfare and Institutions Code section 11200 in accordance with PCC 10353.

  • Priority In any public offering of equity securities of the Issuer (including pursuant to Article IV or Article V), if any Managing Underwriter determines in good faith that the registration of all or part of such securities requested to be included would have a material and adverse effect on the success of such offering, then the securities to be included in such offering shall be reduced by the Managing Underwriter as follows: (a) with respect to any Registration, (i) first, from any Issuer Securities or other securities (other than debt securities, or non-participating preferred equity securities, not exchangeable for or convertible into or otherwise linked to the common equity of the Issuer) for the account of the Issuer and any Person other than the Stockholder proposed to be included in such offering, until such Issuer Securities have, if necessary, been reduced to zero; and (ii) second, subject to clause (c) below, from any Registrable Securities held by the Stockholder; (b) with respect to any other public offering, (i) first, from any Registrable Securities held by the Stockholder to be included in such offering, until such Registrable Securities have, if necessary, been reduced to zero; and (ii) second, from any Issuer Securities or other securities (other than debt securities, or non-participating preferred equity securities, not exchangeable for or convertible into or otherwise linked to the common equity of the Issuer) for the account of the Issuer and any stockholder of the Issuer other than the Stockholder proposed to be included in such offering. Notwithstanding the foregoing, no reduction pursuant to this Section 6.9 shall be made in the number of Initial Registrable Securities required to be included in the Initial Registration or the Initial Sale pursuant to Sections 2.1 and 4.1 unless one or more holders of Issuer Securities other than the Stockholder and the Issuer are participating in the Initial Registration or the Initial Sale, in which case such reduction shall be made pro rata (unless the stockholders participating in the offering agree otherwise, subject to the proviso below) as to all securities (other than debt securities, or non-participating preferred equity securities, not exchangeable for or convertible into or otherwise linked to the common equity of the Issuer) proposed to be included in such offering; provided, however, that in all events, following any such reductions, such offering shall include a number of shares of Class A Common Stock equal to or greater than the Initial Number of Shares. If the number of shares of Class A Common Stock sold by the Stockholder and the other selling stockholders in such offering equals or exceeds the Initial Number of Shares, the Stockholder shall be deemed to have satisfied its obligations under Section 2.1(b)(ii).

  • Default in Favor of Third Parties Borrower or any Grantor defaults under any loan, extension of credit, security agreement, purchase or sales agreement, or any other agreement, in favor of any other creditor or person that may materially affect any of Borrower's or any Grantor's property or Borrower's or any Grantor's ability to repay the Loans or perform their respective obligations under this Agreement or any of the Related Documents.

  • DIP Financing (a) If the Company or any Grantor shall be subject to any Insolvency Proceeding at any time prior to the Discharge of ABL Obligations, and the ABL Collateral Agent or the ABL Secured Parties shall seek to provide the Company or any Grantor with, or consent to a third party providing, any financing under Section 364 of the Bankruptcy Code or consent to any order for the use of cash collateral constituting Receivables Collateral under Section 363 of the Bankruptcy Code (each, a “DIP Financing”), with such DIP Financing to be secured by all or any portion of the Receivables Collateral (including assets that, but for the application of Section 552 of the Bankruptcy Code would be Receivables Collateral) but not any other asset or any Non-Receivables Collateral, then the New First Lien Collateral Agent, on behalf of itself and the New First Lien Secured Parties, agrees that it will raise no objection and will not support any objection to such DIP Financing or use of cash collateral or to the Liens securing the same on the grounds of a failure to provide “adequate protection” for the Liens of the New First Lien Collateral Agent securing the New First Lien Obligations or on any other grounds (and will not request any adequate protection solely as a result of such DIP Financing or use of cash collateral that is Receivables Collateral, except as permitted by Section 6.3(b)), so long as (i) the New First Lien Collateral Agent retains its Lien on the Common Collateral to secure the New First Lien Obligations (in each case, including Proceeds thereof arising after the commencement of the case under the Bankruptcy Code); (ii) the terms of the DIP Financing do not compel the applicable Grantor to seek confirmation of a specific plan of reorganization for which all or substantially all of the material terms of such plan are set forth in the DIP Financing documentation or related document; and (iii) all Liens on Common Collateral securing any such DIP Financing shall be senior to or on a parity with the Liens of the ABL Collateral Agent and the ABL Secured Parties securing the ABL Obligations on Common Collateral; provided, however, that nothing contained in this Agreement shall prohibit or restrict the New First Lien Collateral Agent or any New First Lien Secured Party from raising any objection or supporting any objection to such DIP Financing or use of cash collateral or to the Liens securing the same on the grounds of a failure to provide “adequate protection” for the Liens of the New First Lien Collateral Agent on Non-Receivables Collateral securing the New First Lien Obligations. (b) All Liens granted to the ABL Collateral Agent or the New First Lien Collateral Agent in any Insolvency Proceeding, whether as adequate protection or otherwise, are intended by the Parties to be and shall be deemed to be subject to the Lien Priority and the other terms and conditions of this Agreement.

  • Credit Union Lien and Security Interest To the extent you owe the Credit Union money as a borrower, guarantor, indorser or otherwise, the Credit Union has a lien on any or all of the funds in any account in which you have an ownership interest at the Credit Union, regardless of the source of the funds. The Credit Union may apply these funds in any order to pay off your indebtedness without further notice to you. If the Credit Union chooses not to enforce its lien, the Credit Union does not waive its right to enforce the lien at a later time. In addition, you grant the Credit Union a consensual security interest in your accounts and agree the Credit Union may use the funds from your accounts to pay any debt or amount owed the Credit Union, except obligations secured by your dwelling, unless prohibited by applicable law. All accounts are nonassignable and nontransferable to third parties.

  • Juniors 16.1 The minimum wages to be paid to a junior Employees are the following percentages of the Base Rate of pay for ordinary hours worked for the relevant classification: Age % of relevant Base Hourly Rate Up to and including 18 years of age 70 19 years of age 80 20 years of age 100 16.2 Where a junior Employee is aged 18 years or more and is required to drive and be in sole charge of a motor vehicle, they will be paid the adult rate assigned to the class of driving work that they are required to perform.

  • Priority and Liens (a) Subject to Section 2.20(c), each of the Loan Parties hereby covenants and agrees that, upon the entry of the DIP Order, its obligations hereunder and under the Loan Documents: (i) pursuant to Section 364(c)(1) of the Bankruptcy Code, shall at all times constitute an allowed Superpriority Claim in the Cases, subject to any limitations set forth in the DIP Order; (ii) pursuant to Section 364(c)(2) of the Bankruptcy Code, shall at all times be secured by a valid, binding, continuing, enforceable perfected first priority Lien (that is subject to the terms of the Intercreditor Agreement and DIP Order) on all of the property of such Loan Parties, whether now existing or hereafter acquired, that is not subject to valid, perfected, non-voidable liens in existence at the time of commencement of the Cases or to valid, non-voidable liens in existence at the time of such commencement that are perfected subsequent to such commencement as permitted by Section 546(b) of the Bankruptcy Code (limited, in the case of voting equity interests of CFC’s, 65% of the voting equity interests); (iii) pursuant to Section 364(c)(3) of the Bankruptcy Code, shall be secured by a valid, binding, continuing, enforceable perfected second Lien upon all property of such Loan Parties, whether now existing or hereafter acquired, that is subject to valid, perfected and non-voidable Liens in existence at the time of the commencement of the Cases or that is subject to valid Liens in existence at the time of the commencement of the Cases that are perfected subsequent to such commencement as permitted by Section 546(b) of the Bankruptcy Code (other than certain property that is subject to the existing Liens that secure obligations in respect of the Existing Second Lien Debt, which liens shall be primed by the liens described in the following clause (iv)); and (iv) pursuant to Section 364(d)(1) of the Bankruptcy Code, shall be secured by a valid, binding, continuing, enforceable perfected first priority senior priming Lien on all of the property of such Loan Parties that is subject to the existing liens which secure the Existing Second Lien Debt (collectively, the “Primed Liens”), all of which Primed Liens shall be primed by and made subject and subordinate to (to the extent set forth in the DIP Order) the perfected first priority senior Liens to be granted to the Agent, which senior priming Liens in favor of the Agent shall also prime any Liens granted after the commencement of the Cases to provide adequate protection Liens in respect of any of the Primed Liens, subject in each case to the Carve-Out and as set forth in the DIP Order and the Intercreditor Agreement. (a) As to all real property the title to which is held by a Loan Party (other than any Loan Party that is not a Debtor) or the possession of which is held by any such Loan Party pursuant to leasehold interest, such Loan Parties hereby assign and convey as security, grant a security interest in, hypothecate, mortgage, pledge and set over unto the Agent on behalf of the Lenders all of the right, title and interest of such Loan Parties in all of such owned real property and in all such leasehold interests, together in each case with all of the right, title and interest of such Loan Parties in and to all buildings, improvements, and fixtures related thereto, any lease or sublease thereof, all general intangibles relating thereto and all proceeds thereof. Such Loan Parties acknowledge that, pursuant to the DIP Order, the Liens in favor of the Agent on behalf of the Lenders in all of such real property and leasehold instruments of such Loan Parties shall be perfected without the recordation of any instruments of mortgage or assignment. Such Loan Parties further agree that, upon the request of the Agent, in the exercise of its business judgment, such Loan Parties shall enter into separate fee and leasehold mortgages in recordable form with respect to such properties on terms satisfactory to the Agent and including customary related deliverables, including, without limitation, a Standard Flood Hazard Determination and, to the extent applicable, a notification to the applicable Loan Party that that flood insurance coverage under the National Flood Insurance Program is not available or evidence of flood insurance with respect to such property consistent with the requirements set forth in Section 5.01(c). (b) The relative priorities of the Liens described in this Section 2.20 with respect to the Collateral shall be as set forth in the DIP Order and the Intercreditor Agreement. The relative priorities of the First Lien First Out Loans, the First Lien Last OutNew Money Loans and the Junior Loans shall be as set forth in the DIP Order and Section 6.02. All of the Liens described in this Section (c) Notwithstanding anything to the contrary herein, not more than 65% of the voting equity interests of any CFC or a Subsidiary of a CFC shall be pledged in favor of any Lender or the Agent.

  • Permitted Liens; Title Insurance Each Mortgaged Property securing a Mortgage Loan is covered by an American Land Title Association loan title insurance policy or a comparable form of loan title insurance policy approved for use in the applicable jurisdiction (or, if such policy is yet to be issued, by a pro forma policy, a preliminary title policy or a “marked up” commitment, in each case with escrow instructions and binding on the title insurer) (the “Title Policy”) in the original principal amount of such Mortgage Loan (or with respect to a Mortgage Loan secured by multiple properties, an amount equal to at least the allocated loan amount with respect to the Title Policy for each such property) after all advances of principal (including any advances held in escrow or reserves), that insures for the benefit of the owner of the indebtedness secured by the Mortgage, the first priority lien of the Mortgage (which lien secures the related Whole Loan, in the case of a Mortgage Loan that is part of a Whole Loan), which lien is subject only to (a) the lien of current real property taxes, water charges, sewer rents and assessments not yet due and payable; (b) covenants, conditions and restrictions, rights of way, easements and other matters of public record specifically identified in the Title Policy; (c) the exceptions (general and specific) and exclusions set forth in such Title Policy; (d) other matters to which like properties are commonly subject; (e) the rights of tenants (as tenants only) under leases (including subleases) pertaining to the related Mortgaged Property; (f) if the related Mortgage Loan constitutes a Crossed Underlying Loan, the lien of the Mortgage for another Mortgage Loan contained in the same Crossed Mortgage Loan Group, and (g) condominium declarations of record and identified in such Title Policy, provided that none of clauses (a) through (g), individually or in the aggregate, materially and adversely interferes with the value or principal use of the Mortgaged Property, the security intended to be provided by such Mortgage, or the current ability of the related Mortgaged Property to generate net cash flow sufficient to service the related Mortgage Loan or the Mortgagor’s ability to pay its obligations when they become due (collectively, the “Permitted Encumbrances”). For purposes of clause (a) of the immediately preceding sentence, any such taxes, assessments and other charges shall not be considered due and payable until the date on which interest and/or penalties would be payable thereon. Except as contemplated by clause (f) of the second preceding sentence none of the Permitted Encumbrances are mortgage liens that are senior to or coordinate and co-equal with the lien of the related Mortgage. Such Title Policy (or, if it has yet to be issued, the coverage to be provided thereby) is in full force and effect, all premiums thereon have been paid and no claims have been made by the Mortgage Loan Seller thereunder and no claims have been paid thereunder. Neither the Mortgage Loan Seller, nor to the Mortgage Loan Seller’s knowledge, any other holder of the Mortgage Loan, has done, by act or omission, anything that would materially impair the coverage under such Title Policy. Each Title Policy contains no exclusion for, or affirmatively insures (except for any Mortgaged Property located in a jurisdiction where such affirmative insurance is not available in which case such exclusion may exist), (a) that the Mortgaged Property shown on the survey is the same as the property legally described in the Mortgage and (b) to the extent that the Mortgaged Property consists of two or more adjoining parcels, such parcels are contiguous.

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!