Standards, References, and Specifications Sample Clauses

Standards, References, and Specifications. This Exhibit 6 outlines the process to be used by the Phase Developer when performing Predevelopment Work and creating the required standards and references for the Section Work as part of the Predevelopment Work. At a minimum, Work shall comply with Applicable Law. The Technical Provisions have been prepared reflecting the use of MDOT or VDOT standards, specifications policies and procedures. MDOT and VDOT standards, specifications policies and procedures also include standard MDOT SHA Special Provisions, Special Provision Inserts, standard details, VDOT Special Provisions, Copied Notes and similar documents. The Phase Developer is also advised that Work on Elements owned or maintained by local jurisdictions may also need to be designed and constructed to standards, specifications, policies and procedures issued by the local jurisdiction. The Phase Developer may propose to use alternate standards or specifications, subject to review and acceptance by MDOT. Any alternate standards, specifications policies or procedures proposed by the Phase Developer shall perform equal to or better than the pertinent MDOT or VDOT standards, specifications policies and procedures. A list of potential references, standards, codes and guidelines is included as Appendix B to this Exhibit 6. The list of documents is provided for the Phase Developer’s convenience and is not to be considered comprehensive. As part of the Predevelopment Work, provide any alternate standards, specifications policies and procedures that the Phase Developer proposes are applied to the Work, subject to review and acceptance by MDOT. All standards and references used for Section Work shall:  be current versions of these documents as of the Setting Date for the pertinent Section; and  meet the same requirements for equal or better if alternate standards are proposed. The Section Technical Proposal shall identify the standard specifications to be used for the Work. When using standard specifications, the terms used in the standard specifications may need to be further clarified or revised to make the standard specifications align with the P3 Program. For example, if using the MDOT SHA Standard Specifications for Construction and Materials references to the contractor, the bidder, the engineer or the inspector would need modification for clarity to align with the P3 Program. Changes to the Section specifications as the Design Work advances shall be submitted and are subject to review and acceptance by ...
Sample 1
AutoNDA by SimpleDocs

Related to Standards, References, and Specifications

  • Specifications and Standards a) All articles supplied shall strictly conform to the specifications, trademark laid down in the bidding document and wherever articles have been required according to ISI/ ISO/ other applicable specifications/ certifications/ standards, those articles should conform strictly to those specifications/ certifications/ standards. The supply shall be of best quality and description. The decision of the competent authority/ purchase committee whether the articles supplied conforms to the specifications shall be final and binding on the supplier/ selected bidder.

  • Technical Specifications The Technical Specifications furnished on the CD are intended to establish the standards for quality, performance and technical requirements for all labor, workmanship, material, methods and equipment necessary to complete the Work. When specifications and drawings are provided or referenced by the County, these are to be considered part of the Scope of Work, and to be specifically documented in the Detailed Scope of Work. For convenience, the County supplied specifications, if any, and the Technical Specifications furnished on the CD.

  • General specifications 6.1.1. A vehicle and its electrical/electronic system(s) or ESA(s) shall be so designed, constructed and fitted as to enable the vehicle, in normal conditions of use, to comply with the requirements of this Regulation.

  • Technical Standards Applicable to a Wind Generating Plant i. Low Voltage Ride-Through (LVRT) Capability A wind generating plant shall be able to remain online during voltage disturbances up to the time periods and associated voltage levels set forth in the standard below. The LVRT standard provides for a transition period standard and a post-transition period standard.

  • Technical Specification As enumerated in Special Conditions of Contract/Scope of Work/attached Drawing/ Details/Schedule of Rates.

  • DAF Specifications Developer shall submit initial specifications for the DAF, including System Protection Facilities, to Connecting Transmission Owner and NYISO at least one hundred eighty (180) Calendar Days prior to the Initial Synchronization Date; and final specifications for review and comment at least ninety (90) Calendar Days prior to the Initial Synchronization Date. Connecting Transmission Owner and NYISO shall review such specifications to ensure that the DAF are compatible with the technical specifications, operational control, and safety requirements of the Connecting Transmission Owner and NYISO and comment on such specifications within thirty (30) Calendar Days of Developer’s submission. All specifications provided hereunder shall be deemed to be Confidential Information.

  • Technical Specifications and Drawings a) The Goods and Related Services supplied under this Contract shall conform to the technical specifications and standards mentioned in Section VI, Schedule of Requirements and, when no applicable standard is mentioned, the standard shall be equivalent or superior to the official standards whose application is appropriate to the Goods' country of origin.

  • Drawings and Specifications 9.1 A complete list of all Drawings that form a part of the Contract Documents are to be found as an index on the Drawings themselves, and/or may be provided to Developer and/or in the Table of Contents.

  • REFERENCE STANDARDS A. Standards, Specifications, Codes, Laws, and Regulations

  • The Specifications The Specifications are that portion of the Contract Documents consisting of the written requirements for materials, equipment, systems, standards and workmanship for the Work, and performance of related services.

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!