STORAGE AND PROTECTION Sample Clauses
STORAGE AND PROTECTION. Coordinate the shipping of plants and excavation of holes to ensure minimum time laps between digging and planting.
STORAGE AND PROTECTION. Pre-painted steel roofing, xxxxxxx products and accessories should be delivered to the jobsite in strapped bundles. Sheets and/or bundles shall be neatly stacked in the ground and if left in the open it shall be protected by covering the stack materials with loose tarpauline.
STORAGE AND PROTECTION. Board, Board staff, Board subcontractor, and Board subcontractor staff shall store and process TWC Information in a place physically secure from access by unauthorized persons by any means.
STORAGE AND PROTECTION. A. Store and protect products in accordance with manufacturer’s instructions, with seals and labels intact and legible. Store sensitive products in weather-tight, climate controlled enclosures.
B. For exterior storage of fabricated products, place above ground on supports that are sloped for drainage.
C. Provide off-site storage and protection for materials. OWNER is not responsible for material storage or parking.
D. Cover products subject to deterioration with impervious sheet covering. Provide ventilation to avoid condensation.
E. Store loose granular materials on solid flat surfaces in a well-drained area. Prevent mixing with foreign matter.
F. Provide equipment and personnel to store products by methods to prevent soiling, disfigurement, or damage.
G. Arrange storage of products to permit access for inspection. Periodically inspect to assure products are undamaged and are maintained under specified conditions.
STORAGE AND PROTECTION. .1 Prevent damage to fencing, trees, existing buildings, utility lines, root systems of trees and any other items which are designated to remain.
.1 Repair any damaged items to approval of Project Coordinator.
.2 Replace any trees designated to remain, if damaged, as directed by Project Coordinator.
2.1 PREPARATION
STORAGE AND PROTECTION. A. Store products in accordance with manufacturer's instructions, with seals and labels intact and legible. Store sensitive products, including factory-finished items and similar work, in weather-tight enclosures; maintain within temperature and humidity ranges required by manufacturer's instructions. Comply with applicable laws, ordinances and regulations for protective storage of potentially dangerous materials.
B. For exterior storage of fabricated products, place on sloped supports above ground. Cover products subject to deterioration with impervious sheet covering; provide ventilation to avoid condensation.
C. Store loose granular materials on solid surfaces in a well-drained area and prevent mixing with foreign matter.
D. Arrange storage to provide access for inspection at all times. Periodically inspect to assure products are free from damage or deterioration, and are maintained under required conditions.
E. At end of each day's work, cover new work likely to be damaged. Provide substantial coverings necessary to protect installed products from damage, traffic, and subsequent construction operations. Refer to Section 01 50 00 for additional requirements, including removal of temporary protections.
F. Contractor shall provide inspection of Subcontractor's material for compliance with submittals on proper storage. PART 2 - PRODUCTS NOT USED PART 3 - EXECUTION NOT USED PART 1 - GENERAL
1.01 SECTION INCLUDES: A. Performance requirements.
STORAGE AND PROTECTION. 1 Store materials indoors in dry location and in accordance with manufacturer's recommendations in clean, dry, well-ventilated area. .2 Replace defective or damaged materials with new.
STORAGE AND PROTECTION. A. Provide protection of stored materials and products against theft, casualty, or deterioration.
B. Designate receiving/storage areas for incoming products so that they are delivered according to installation schedule and placed convenient to work area in order to minimize waste due to
STORAGE AND PROTECTION. A. Refer to the Contract and General Conditions and Specifications Sections for requirements pertaining to storage and protection of materials and equipment.
B. Store products in accordance with manufacturers' instruction, with seals and labels intact and legible. Store sensitive products in weather tight enclosures; maintain within temperature and humidity ranges required by manufacturers' instructions.
C. For exterior storage of fabricated products, place on sloped supports above ground. Cover products subject to deterioration with impervious sheet covering; provide ventilation to avoid condensation.
D. Store loose granular materials on solid surfaces in a well-drained area; prevent mixing with foreign matter.
E. Arrange storage to provide access for inspection. Periodically inspect to assure that products are undamaged, and are maintained under required conditions.
STORAGE AND PROTECTION. 1 Store and handle piling in accordance with manufacturer’s written instructions to prevent permanent deflection, distortion or damage.