Test Lines Sample Clauses

Test Lines. APC shall assign three or seven digit test line numbers in accordance with BA’s standard numbering arrangements. BA will provide APC with preferred number assignments for 100-type test lines (balance/quiet), 102-type test lines (kilowatt), and 105-type test lines (automatic transmission measuring).
AutoNDA by SimpleDocs
Test Lines. 12.3.1. Prior to the manufacturing of the Systems, the Supplier shall manufacture first a prototype of one short checkpoint line and one long checkpoint line of the System, based on the requirements specified in the Technical Specifications (the “Test Lines”). The Test Lines will be tested in the Supplier's factory by the IAA's representatives as further described in the Technical Specifications. After successful completion of such tests, the Test Lines will be installed in Xxx Xxxxxx Terminal 3 and/or at any other location as will be required by the IAA where the tests will be conducted when the System will also be connected to the screening machines.
Test Lines. PriCellular shall assign three or seven digit test line numbers in accordance with BA’s standard numbering arrangements. BA will provide PriCellular with preferred number assignments for 100-type test lines (balance/quiet), 102-type test lines (kilowatt), and 105-type test lines (automatic transmission measuring).

Related to Test Lines

  • Computer Equipment Recycling Program If this Contract is for the purchase or lease of computer equipment, then Contractor certifies that it is in compliance with Subchapter Y, Chapter 361 of the Texas Health and Safety Code related to the Computer Equipment Recycling Program and the Texas Commission on Environmental Quality rules in 30 TAC Chapter 328.

  • Monitoring Equipment 2.2.1 24-hour TSP air quality monitoring was performed using High Volume Sampler (HVS) located at each designated monitoring station. The HVS meets all the requirements of the Project Specific EM&A Manual. Portable direct reading dust meters were used to carry out the 1-hour TSP monitoring. Brand and model of the equipment is given in Table 2.1.

  • Test equipment For the tests an inertia dynamometer shall be equipped with the vehicle brake in question. The dynamometer shall be instrumented for continuous recording of rotational speed, brake torque, pressure in the brake line, number of rotations after brake application, braking time and brake rotor temperature.

  • Software Components At any time during the contract period of performance, the Government may require the Contractor to remedy any failure of the software to comply with the requirements of this contract. Support shall consist of correction of errors, provision of modifications, improvements, and other products the original manufacturer makes available to the Government without charge. The Government shall also be provided full documentation of changes and/or modifications to the software provided to meet the Government's requirements.

  • Network Interface Device (NID) 2.7.1 The NID is defined as any means of interconnection of end-user customer premises wiring to BellSouth’s distribution plant, such as a cross-connect device used for that purpose. The NID is a single-line termination device or that portion of a multiple-line termination device required to terminate a single line or circuit at the premises. The NID features two independent xxxxxxxx or divisions that separate the service provider’s network from the end user’s customer-premises wiring. Each chamber or division contains the appropriate connection points or posts to which the service provider and the end user each make their connections. The NID provides a protective ground connection and is capable of terminating cables such as twisted pair cable.

  • Program Components Activities and services delivered under this Program Element align with Foundational Programs and Foundational Capabilities, as defined in Oregon’s Public Health Modernization Manual, (xxxx://xxx.xxxxxx.xxx/oha/PH/ABOUT/TASKFORCE/Documents/public_health_modernization_man ual.pdf) as well as with public health accountability outcome and process metrics (if applicable) as follows:

  • Access to Network Interface Device (NID 2.4.3.1. Due to the wide variety of NIDs utilized by BellSouth (based on subscriber size and environmental considerations), Mpower may access the on-premises wiring by any of the following means: BellSouth shall allow Mpower to connect its loops directly to BellSouth’s multi-line residential NID enclosures that have additional space and are not used by BellSouth or any other telecommunications carriers to provide service to the premise. Mpower agrees to install compatible protectors and test jacks and to maintain the protection system and equipment and to indemnify BellSouth pursuant to Section 8 of the General Terms and Conditions of this Agreement.

  • Picket Lines The Employer agrees that, in the event of a legal picket line of another trade union being in existence at any of the Employer's stores within the Bargaining Unit, the Employer will in no way require or force members to report to work behind such a picket line. Nor will the Employer discipline or in any way discriminate against an employee who refuses to report to work while a legal picket line exists at his or her place of work.

  • Access Toll Connecting Trunk Group Architecture 9.2.1 If CBB chooses to subtend a Verizon access Tandem, CBB’s NPA/NXX must be assigned by CBB to subtend the same Verizon access Tandem that a Verizon NPA/NXX serving the same Rate Center Area subtends as identified in the LERG.

  • Television Equipment Recycling Program If this Contract is for the purchase or lease of covered television equipment, then Contractor certifies that it is compliance with Subchapter Z, Chapter 361 of the Texas Health and Safety Code related to the Television Equipment Recycling Program.

Time is Money Join Law Insider Premium to draft better contracts faster.