Commissioning Spares Sample Clauses
The 'Commissioning Spares' clause defines the requirements and procedures for providing spare parts necessary during the commissioning phase of a project or equipment installation. Typically, this clause specifies the types and quantities of spares to be supplied, the timing of their delivery, and responsibilities for their storage and use. For example, it may require the contractor to provide extra fuses, filters, or other consumables to ensure smooth system startup and testing. The core function of this clause is to minimize delays and operational disruptions during commissioning by ensuring that essential replacement parts are readily available.
POPULAR SAMPLE Copied 1 times
Commissioning Spares. The Contractor shall supply with the Equipment a sufficient quantity of spares for operation of the Equipment within the period of commissioning of the Plant.
Commissioning Spares. Seller’s representative price list of start-up and commissioning spares and a representative list of special tools needed during start-up and commissioning are set forth in Exhibit M. Seller shall within the Purchase Amount provide (i) all spare parts necessary to achieve installation, start up, commissioning, Performance Testing, and (ii) all installation and maintenance tools that are not normally found available in the market place and therefore the attached lists may not be all inclusive. 3.14.2 O & M Spare Parts3.14.2 O & M Spare Parts. 3.14.2.1 O & M Spare Parts3.14.2.1
Commissioning Spares. The Contractor shall provide special tools, consumables and a set of recommended spares as part of the contract and tender price evaluation.
Commissioning Spares. 5.2.1 The Contractor shall supply along with the Materials, commissioning spares considering allowances as per experience of the Contractor to cover wastage / breakage during transportation, storage, handling, construction, erection, testing and commissioning (“Commissioning Spares”). The Contractor shall be fully responsible for ensuring availability of adequate quantities of Commissioning Spares at the Site. If Commissioning Spares supplied are found to be inadequate, the Contractor shall supply additional Commissioning Spares promptly at his own cost.
Commissioning Spares. One Set of Gaskets and Filter Element (Screen) to be supplied along with the main supply of strainer. INTENDED SERVICE PERMANENT STRAINER – WATER LINES. PRESSURE TEMP. RATING ANSI B 16.34 MATERIALS AS SPECIFIED IN TABLE I. CONSTRUCTION Basket Strainer with replaceable filter element END CONNECTIONS: FLANGED Upto 24” As per ANSI B16.5 #150 FF OR RF as specified in variant table. SCREEN SS 304 [40mesh] BACK UP SCREEN PERFORATED SS BACK UP SCREEN SHALL BE PROVIDED. Refer Doc LAYOUTS & PIPING ENGINEERING PROJECT ENGINEERING & SYSTEMS DIVISION PREPARED CHECKED APPROVED DATE VUK ▇▇▇ ▇ ▇▇▇▇▇▇▇▇ 31.07.18 SL No Part Name Material 01 Housing A 106 GR-B 02 End Flanges A 105 , As per ANSI B16.5 03 Gasket NAB MSW (SS316)+ PTFE FILL for up to 24” 05 Vent & Drain ASTM A 105 , 1” NPT with SS plugs 06 Screen Retainer Perforated SS304 sheet along with stiffener rings 07 DP provision 1/2” NPT (F)-4 NO’S, WITH SS PLUGS 08 Support legs ISA 75 09 Dish-end ASTM A 234 WPB-Welded.-sch std-B16.9 o. #1 Form No: Attachm PE&SD enBt:HPRARDAOTCSH–EAMVAYINE–L1E9C00T1R4I1C2A31L-SFRLIAMMIETWEDORK PROJECT ENGINEERING & SYSTEMS DIVISION -PSYTR5A2IN2E4R7S.pdf PURCHASE SPECIFICATION Rev. No. 01
Commissioning Spares. The Contractor shall supply with the Equipment a quantity of spares sufficient for <insert> year(s) operation of the converted production line, after installation and commissioning.