Design Development Phase Drawings Sample Clauses

Design Development Phase Drawings. Provide drawings that indicate the scope of work included in the bid package with sufficient detail to enable preparation and review of an accurate cost estimate, including but not limited to, the following descriptions of minimum requirements for a design development submittal, which shall be augmented as necessary to show design intent and to prepare an accurate estimate of construction cost.
Sample 1Sample 2See All (4)
AutoNDA by SimpleDocs
Design Development Phase Drawings. Provide preliminary drawings that indicate the scope of work included in the bid package with sufficient detail to enable preparation and review of an accurate cost estimate, including without limitation, the following descriptions of minimum requirements for a design development submittal, which shall be augmented as necessary to show design intent and to prepare an accurate estimate of construction cost in its essentials as to kinds and locations of materials; type of structural, mechanical and electrical systems. Architectural Preliminary Drawings Floor plans that clearly show: Finish schedule Principal dimensions Wall types clearly identified Security zones and perimeters Room and door numbers, and a numbering plan for the entire facility Sufficient sections and details to enable a reasonable material takeoff Contractor-furnished and Owner-furnished equipment list incorporated in layout Roof plans that clearly show: Slopes (No interior valley’s) Type of roofing (District standard: 60 mil. white single ply with walkways pads) Roof access and pathways, include fall protection tie-off’s, features. Location of any mechanical equipment Sufficient information to determine primary and secondary means of drainage Reflected ceiling plans that clearly show: Ceiling material Access hatches Room numbers Partitions coordinated with the floor plans Mechanical and electrical features coordinated with mechanical and electrical system drawings Elevations that clearly show: Types of surface materials Dimensions from finish floor to tops of walls, xxxxx and roof lines All openings without dimensions but coordinated with door and window schedules Sections that clearly show: Any security considerations Firewall conditions at tops of walls All essential building parts and materials—low/no maintenance finishes. All door, window, glazing and hardware schedules complete with sufficient detail to show the agreed-upon form and style All items intended to be permanently affixed to the building Structural Preliminary Drawings Floor framing and foundations plans that clearly show: Principal dimensions All columns, shear walls, shafts and stairs Coordination of structure with architectural floor plans Sections cut and details to identify the proposed type of foundations Sufficient section and detail bubbles to show where sections and details can be found All major framing members with sizes Roof framing plans that clearly show: Principal dimensions All major framing members with siz...
Sample 1

Related to Design Development Phase Drawings

  • Design Development Phase INDICATE IN STATEMENT OF WORK “NOT APPLICABLE” IF SECTION IS NOT APPLICABLE

  • Development Phase contractual phase initiated with the approval of ANP for the Development Plan and which is extended during the Production Phase while investments in xxxxx, equipment, and facilities for the Production of Oil and Gas according to the Best Practices of the Oil Industry are required.

  • Design Development Phase Services 3.3.1 Based on the Owner’s approval of the Schematic Design Documents, and on the Owner’s authorization of any adjustments in the Project requirements and the budget for the Cost of the Work, the Architect shall prepare Design Development Documents for the Owner’s approval. The Design Development Documents shall illustrate and describe the development of the approved Schematic Design Documents and shall consist of drawings and other documents including plans, sections, elevations, typical construction details, and diagrammatic layouts of building systems to fix and describe the size and character of the Project as to architectural, structural, mechanical and electrical systems, and other appropriate elements. The Design Development Documents shall also include outline specifications that identify major materials and systems and establish, in general, their quality levels.

  • Design Development An interim step in the design process. Design Development documents consist of plans, elevations, and other drawings and outline specifications. These documents will fix and illustrate the size and character of the entire project in its essentials as to kinds of materials, type of structure, grade elevations, sidewalks, utilities, roads, parking areas, mechanical and electrical systems, and such other work as may be required.

  • Design Phase All Basic Services set forth in the Agreement with the exception of Interdisciplinary Document Coordination Review, conducting a Card Trick session, Value-Engineering services, Estimating services. Bidding Phase • All Basic Services set forth in the Agreement. Construction Phase • All Basic Services set forth in the Agreement. Post-Construction • All Basic Services set forth in the Agreement.

  • Design Development Documents See Section 2, Part 1, Article 2.1.5.

  • Working Drawings Not later than 15 business days following the approval of the TI Design Drawings by Landlord, Tenant shall cause the TI Architect to prepare and deliver to Landlord for review and comment construction plans, specifications and drawings for the Tenant Improvements (“TI Construction Drawings”), which TI Construction Drawings shall be prepared substantially in accordance with the TI Design Drawings. Tenant shall be solely responsible for ensuring that the TI Construction Drawings reflect Tenant’s requirements for the Tenant Improvements. Landlord shall deliver its written comments on the TI Construction Drawings to Tenant not later than 10 business days after Landlord’s receipt of the same; provided, however, that Landlord may not disapprove any matter that is consistent with the TI Design Drawings. Tenant and the TI Architect shall consider all such comments in good faith and shall, within 10 business days after receipt, notify Landlord how Tenant proposes to respond to such comments. Any disputes in connection with such comments shall be resolved in accordance with Section 2(d) hereof. Provided that the design reflected in the TI Construction Drawings is consistent with the TI Design Drawings, Landlord shall approve the TI Construction Drawings submitted by Tenant. Once approved by Landlord, subject to the provisions of Section 4 below, Tenant shall not materially modify the TI Construction Drawings except as may be reasonably required in connection with the issuance of the TI Permit (as defined in Section 3(a) below).

  • Shop Drawings All drawings, prints, diagrams, illustrations, brochures, schedules, and other data that are prepared by Developer, a subcontractor, manufacturer, supplier, or distributor, that illustrate how specific portions of the Work shall be fabricated or installed.

  • Technical Specifications and Drawings a) The Goods and Related Services supplied under this Contract shall conform to the technical specifications and standards mentioned in Section VI, Schedule of Requirements and, when no applicable standard is mentioned, the standard shall be equivalent or superior to the official standards whose application is appropriate to the Goods' country of origin.

  • Construction Drawings After approving the Additional Programming Information, Landlord shall cause the Architect and the Engineers to prepare and deliver to Tenant Construction Drawings that conform to the approved Space Plan and the approved Additional Programming Information. Such preparation and delivery shall occur within 15 business days after the later of Landlord’s approval of the Additional Programming Information or the mutual execution and delivery of this Agreement. Tenant shall approve or disapprove the Construction Drawings by notice to Landlord. If Tenant disapproves the Construction Drawings, Tenant’s notice of disapproval shall specify any revisions Tenant desires in the Construction Drawings. After receiving such notice of disapproval, Landlord shall cause the Architect and/or the Engineers to revise the Construction Drawings, taking into account the reasons for Tenant’s disapproval (provided, however, that Landlord shall not be required to cause the Architect or the Engineers to make any revision to the Construction Drawings that is inconsistent with the Landlord Requirements or that Landlord otherwise reasonably disapproves), and resubmit the Construction Drawings to Tenant for its approval. Such revision and resubmission shall occur within five (5) business days after the later of Landlord’s receipt of Tenant’s notice of disapproval or the mutual execution and delivery of this Agreement if such revision is not material, and within such longer period of time as may be reasonably necessary (but not more than 15 business days after the later of such receipt or such mutual execution and delivery) if such revision is material. Such procedure shall be repeated as necessary until Tenant has approved the Construction Drawings. The Construction Drawings approved by Landlord and Tenant are referred to in this Work Letter as the “Approved Construction Drawings”.

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!