Installation of Metering Equipment Sample Clauses

Installation of Metering Equipment. Metering equipment shall be designed, furnished, installed, owned, inspected, tested, maintained and replaced as provided in the Generation Interconnection Agreement; provided, however, that PacifiCorp acting in its merchant function capacity shall be under no obligation, pursuant hereto, to bear any expense relating to such metering equipment.
Sample 1Sample 2Sample 3See All (24)
AutoNDA by SimpleDocs
Installation of Metering Equipment. At Seller’s cost and expense, Seller shall design, furnish, install, own, inspect, test, maintain, and replace all metering equipment as required by the Generation Interconnection Agreement and this Section 9. Seller must use revenue grade metering equipment consistent with American National Standards Institute (“ANSI”) standards. In the event Market Operator adopts new meter requirements that are applicable to the Facility, Seller will, at its cost and expense, reasonably cooperate to upgrade any applicable metering equipment. Seller shall reasonably cooperate with Utility in developing any metering protocols necessary for Utility to comply with the requirements of the Market Operator or Utility Transmission.
Sample 1Sample 2Sample 3See All (8)
Installation of Metering Equipment. At Seller’s cost and expense, Seller shall design, furnish, install, own, inspect, test, maintain and replace all metering equipment required by the Generation Interconnection Agreement and this Section 9. Seller shall reasonably cooperate with PacifiCorp in developing any metering protocols necessary for PacifiCorp to comply with the requirements of the Market Operator.
Sample 1Sample 2Sample 3See All (5)
Installation of Metering Equipment. 6.1 Horizon Power will, as soon as reasonably practicable after the Contract Commencement Date, supply and install any Metering Equipment required to be installed at the Premises to facilitate the measurement and sale of Distributed Energy Exported by the Customer to Horizon Power under the Contract. The Customer must provide a safe and secure place, which also complies with the relevant Legal Requirements, for installation and operation of that Metering Equipment. 6.2 The Customer must pay all costs associated with: (a) the supply and installation of new Metering Equipment at the Premises; or (b) the reprogramming of Metering Equipment existing at the Premises, by Horizon Power under clause 6.1, at the prices set out in the Energy Operators (Regional Power Corporation) (Charges) By-laws 2006 (WA), and otherwise at the prices published by Horizon Power from time to time which are, as at the Contract Commencement Date, the prices as set out in section 4 of the Pricing Schedule. The parties acknowledge and agree that “the prices published by Horizon Power from time to time” means that: (c) prices may be varied (either increased or decreased); (d) prices may no longer be payable; or (e) where no price was payable, prices may become payable. The Customer must pay those costs within 14 days of receiving an invoice for those costs from Horizon Power (regardless of whether the Customer System is, or is to be, installed or commissioned). 6.3 The Metering Equipment is not transferable to any other place and, once installed, remains installed at the Premises. The Metering Equipment always remains the property of Horizon Power. 6.4 The Customer must provide access and all reasonable assistance to Horizon Power in order for it to install, program, reprogram and maintain any Metering Equipment at the Premises. 6.5 In the event of any delay in the installation, programming or reprogramming of the Metering Equipment Horizon Power will, to the extent permitted by law, have no liability for any loss to the Customer (including where arising out of negligence).
Sample 1Sample 2
Installation of Metering Equipment. At Seller’s expense, metering equipment must be designed, furnished, installed, owned, inspected, tested, maintained and replaced as provided in the Generation Interconnection Agreement. Seller must reasonably cooperate with PacifiCorp in developing any metering protocols necessary for PacifiCorp to comply with the requirements of the Market Operator.‌
Sample 1Sample 2
Installation of Metering Equipment. The LTA shall include Metering Equipment which shall be utilized to measure and record the Energy received by the LTA at the Interconnection Points or delivered by the LTA to the Interconnection Points, including power quality parameters specified by the NLSO. Labrador Transco shall comply with all Applicable Law regarding the supply, installation and maintenance of the Metering Equipment which shall meet the applicable requirements established by Measurement Canada. Applicable requirements include, but are not limited to, ensuring the meters are sealed by Measurement Canada and ensuring that the re- seal/re-test of the meters is completed when the seal period expires. The Metering Equipment shall be Measurement Canada approved and Labrador Transco shall deliver to Muskrat the notice of approval number issued by Measurement Canada. The LTA shall include one or more back up meters with the capability to record at least 45 days of data at each Interconnection Point. Labrador Transco shall advise the NLSO and Muskrat of any changes to the Metering Equipment in advance or, if advance notice cannot be provided, within 48 hours of the change being made. The NLSO and Muskrat shall each be entitled, upon request, to attend at any meter re- seals/re-tests of Metering Equipment, and to receive copies of the applicable meter test certificates from Labrador Transco.
Sample 1
Installation of Metering Equipment. Sierra shall install the necessary metering and communications equipment to allow for automatic metering of the BPP facility on 00:00 hours on the first day of each month. BPP shall pay for Sierra's actual costs of such installation, up to $5,000. Such installation shall be completed and fully operational prior to January 1, 2003. Sierra shall not require a dedicated communications line for the purpose of meter reading, except and until such time that Sierra has to read the meter manually two (2) times in any calendar year due to the lack of availability of the communications line. In the event of two (2) such manual readings in a calendar year, BPP will, at their sole cost, then be required to install and maintain a dedicated communications line, as approved by Sierra, from that time forward. Such approval shall not be unreasonably withheld.
Sample 1
AutoNDA by SimpleDocs
Installation of Metering Equipment. PacifiCorp shall design, furnish, install, own, inspect, test, maintain and replace all metering equipment required pursuant to the Generation Interconnection Agreement. [
Sample 1
Installation of Metering Equipment. The Seller shall ensure that revenue metering equipment (the “Metering Equipment”) is installed, operated and maintained in accordance with the requirements of FortisBC and the Transmission Authority and the requirements of this section. The Seller shall ensure that the Seller’s Plant is equipped with electronic meters and SCADA capability. The Metering Equipment shall be installed at a location approved by the Buyer, acting reasonably, which location shall be such that the Metering Equipment can measure the Energy generated by the Seller’s Plant independent of any other generation equipment or facilities. The Seller shall ensure that the Metering Equipment is: (a) capable of being remotely interrogated; (b) sufficient to accurately meter the quantity of Test Energy and Eligible Energy; (c) calibrated to measure the quantity of Test Energy and Eligible Energy delivered to the interconnection between the Seller’s Plant and the Fortis System, after adjusting for any line losses from the Seller’s Plant to that interconnection; and (d) in compliance with all requirements set out in the Electricity and Gas Inspection Act (Canada) and associated regulations.
Sample 1

Related to Installation of Metering Equipment

  • Metering Equipment 13.01. Utility will furnish, install, own and maintain metering equipment capable of measuring the flow of kilowatt-hours (kWh) of energy. The Customer's service associated with the CRG will be metered at a single metering point. The metering equipment will measure energy delivered by Utility to Customer and also measure energy delivered by Customer to Utility. Customer agrees to provide safe and reasonable access to the premises for installation of this equipment and its future maintenance or removal.

  • Testing of Metering Equipment Connecting Transmission Owner shall inspect and test all of its Metering Equipment upon installation and at least once every two (2) years thereafter. If requested to do so by NYISO or Developer, Connecting Transmission Owner shall, at Developer’s expense, inspect or test Metering Equipment more frequently than every two (2) years. Connecting Transmission Owner shall give reasonable notice of the time when any inspection or test shall take place, and Developer and NYISO may have representatives present at the test or inspection. If at any time Metering Equipment is found to be inaccurate or defective, it shall be adjusted, repaired or replaced at Developer’s expense, in order to provide accurate metering, unless the inaccuracy or defect is due to Connecting Transmission Owner’s failure to maintain, then Connecting Transmission Owner shall pay. If Metering Equipment fails to register, or if the measurement made by Metering Equipment during a test varies by more than two percent from the measurement made by the standard meter used in the test, Connecting Transmission Owner shall adjust the measurements by correcting all measurements for the period during which Metering Equipment was in error by using Developer’s check meters, if installed. If no such check meters are installed or if the period cannot be reasonably ascertained, the adjustment shall be for the period immediately preceding the test of the Metering Equipment equal to one-half the time from the date of the last previous test of the Metering Equipment. The NYISO shall reserve the right to review all associated metering equipment installation on the Developer’s or Connecting Transmission Owner’s property at any time.

  • Installation of Equipment You represent that there are no legal, contractual or similar restrictions on the installation of the Equipment in the location(s) you have authorized. It is your responsibility to ensure compliance with all applicable building codes, zoning ordinances, homeowners’ association rules, covenants, conditions, and restrictions related to the Service, to pay any fees or other charges, and to obtain any permits or authorizations necessary for the installation or use of the Service (collectively "Legal Requirements"). You are solely responsible for any fines or similar charges for violation of any applicable Legal Requirements. You acknowledge and agree that Viasat or its designated service provider will be required to access your premises and computer to install and maintain the Equipment, including, without limitation, the antenna and its components. Standard Equipment installations performed by Viasat-authorized installers include: (i) installation of the antenna to an outside wall or sloped roof; (ii) travel to and from your Service location within 50 miles of the installer’s office; (iii) cable routed through one exterior wall and one interior wall or floor; (iv) connection of the antenna to the modem using up to 150 feet of cable; (v) connection of the modem to one computer using up to 7 feet of cable; and (vi) required mounting and cabling hardware. Any different or additional installation services or hardware are non-standard and may result in additional charges to be agreed upon between you and the installer. All installations include attaching the Equipment to your computer, installing software on your computer and configuring your computer to optimize the performance of the Internet Service. You confirm that you have reviewed the installation plan and agreed to any associated charges. If you approved a roof mount, you acknowledge the potential risks associated with this type of installation (including, without limitation, with respect to any warranty that applies to your roof or roof membrane). By signing this Agreement, scheduling one or more service or installation visits, and permitting us or our service provider to enter your home, you are authorizing Viasat and its service provider to perform all of the above actions. You are responsible for backing up the data on your computer and we highly recommend that you do so prior to permitting access to us or one of our designated service providers. NEITHER VIASAT NOR ITS SERVICE PROVIDER SHALL HAVE ANY LIABILITY WHATSOEVER FOR ANY LOSSES RESULTING FROM THE EQUIPMENT OR ANY INSTALLATION, REPAIR OR OTHER SERVICES ASSOCIATED WITH THE EQUIPMENT, INCLUDING WITHOUT LIMITATION, DAMAGE TO YOUR PREMISES OR LOSS OF SOFTWARE, DATA OR OTHER INFORMATION FROM YOUR COMPUTER. This limitation does not apply to any damages arising from the gross negligence or willful misconduct of us or one of our designated service providers. Time frames for installation, if any, are not guaranteed and may vary depending on the types of services requested and other factors.

  • Electrical Equipment Residents must use only CSA, UL-approved or Canadian-certified electrical equipment; the rated wattage of light fixtures must never be exceeded; and only replacement bulbs supplied by Waterloo maintenance staff may be used. Do not leave any unattended electrical equipment turned on (i.e. hair straighteners, lights etc.)

  • Ownership and Location of Metering Equipment The Metering Equipment to be constructed, the capability of the Metering Equipment to be constructed, and the ownership thereof, are identified on the attached Schedule C to this ISA.

  • Additional Equipment Additional Equipment may from time to time be added as the subject matter of this Agreement as agreed on by the parties. Any additional property will be added in an amendment describing the property, the monthly rental, security deposit, and stipulated loss value of the additional Equipment. All amendments must be in writing and signed by both parties. Other than by this amendment procedure, this Agreement may not be amended, modified, or altered in any manner except in writing signed by both parties.

  • Equipment Installation In order to meet its obligations under this Agreement, a Party that owns, rents, or leases equipment (the equipment owner) may require installation of such equipment on property owned by another Party (the property owner), provided that the property is being used for an electric utility purpose and that the property owner shall not be required to do so if it would thereby be prevented from performing its own obligations or exercising its rights under this Agreement.

  • Special Equipment The Employer agrees to provide specialty tools, emergency supplies/equipment, testing equipment and safety equipment as needed to perform required duties as determined and authorized by the Chief or designee. The emergency supplies/equipment will include appropriate survival provisions and equipment for each permanent Maintenance Mechanic 4 and the Law Enforcement Communications Systems Supervisor when they are performing duties that would require such provisions and equipment. When necessary, the employer will replenish used or expired survival provisions and damaged and unusable equipment. All supplies and equipment will be returned to the employer when the employee is no longer performing the duties that would require the survival provisions and/or equipment.

  • Furniture, Fixtures and Equipment Sublessee shall have the right to use during the Term the office furnishings and equipment within the Subleased Premises that are identified on Exhibit C attached hereto, as such exhibit may be adjusted by mutual agreement of the parties prior to the Third Floor Premises Delivery Date (the “Furniture”), provided Sublessee may only use the Furniture located in the Second Floor Premises after the Second Floor Commencement Date. The Furniture is provided in its “AS IS, WHERE IS” condition, without representation or warranty whatsoever. Sublessee shall insure the Furniture under the property insurance policy required under the Master Lease, as incorporated herein, and pay all taxes with respect to the Furniture. Sublessee shall maintain the Furniture in good condition and repair, reasonable wear and tear excepted, and shall be responsible for any loss or damage to the same occurring during the Term. Sublessee shall surrender the Furniture to Sublessor upon the termination of this Sublease in the same condition as exists as of the applicable Delivery Date, reasonable wear and tear excepted. Sublessee shall not remove any of the Furniture from the Subleased Premises. Notwithstanding anything to the contrary herein, Sublessee may provide Sublessor with written notice one (1) time not less than forty-five (45) days prior to the Third Floor Premises Delivery Date that lists any items of Furniture that Sublessee does not want to use and Sublessor shall, at no cost to Sublessee, remove such items from the Subleased Premises prior to the Third Floor Premises Delivery Date and such items shall no longer be considered Furniture hereunder. Notwithstanding the foregoing, provided Sublessee is not in default beyond the expiration of any applicable cure or grace period as of the date of the expiration or earlier termination of this Sublease, which condition may be waived by Sublessor in its sole discretion, then upon the expiration or earlier termination of this Sublease, the Furniture shall become the property of Sublessee, and Sublessee shall accept the same in its “AS IS, WHERE IS” condition, without representation or warranty whatsoever except as provided in the Bill of Sale referred to in the following sentence. In the event the Furniture is to become the property of Sublessee upon the expiration or earlier termination of this Sublease pursuant to the terms of the immediately preceding sentence, then Sublessor agrees to execute and deliver to Sublessee a Bill of Sale in the form of Exhibit D attached hereto conveying and transferring to Sublessee the Furniture.

  • New Equipment Where new types of equipment and/or operations, for which rates of pay are not established by this Agreement, are put into use after the ratification date of this Agreement within operations covered by this Agreement, rates governing such operations shall be subject to negotiations between the parties. This paragraph shall apply to all new types of equipment including office and clerical equipment. In the event an agreement cannot be reached within sixty (60) days after the date such equipment is put into use, the matter may shall be submitted to the National Grievance Committee for final disposition. Rates agreed upon or awarded shall be effective as of the date equipment is put to use

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!