Verification Testing Sample Clauses

Verification Testing a. Upon initial parallel operation of the Facility, or any time interface hardware or software is changed, a verification test of Seller-Owned Interconnection Facilities shall be performed by Seller. A qualified individual, hired or employed by the Seller, shall perform the verification testing in accordance with the manufacturer’s published test procedure. Qualified individuals include professional engineers, factory trained and certified technicians, and licensed electricians with experience in testing protective equipment. b. Verification testing shall be performed every four years. All verification tests prescribed by the manufacturer shall be performed. If wires must be removed to perform certain tests, each wire and each terminal shall be clearly and permanently marked. The Seller shall maintain verification test reports for inspection by the Company. Additionally, all inverters shall be verified once per year as follows: the Seller shall operate the load break disconnect switch and verify the Facility automatically shuts down and does not reconnect with the Company System until the Company System continuous normal voltage and frequency have been maintained for a minimum of 5 minutes. The Seller shall maintain a log of these operations for inspection by the Company. c. Any system that depends upon a battery for trip power shall be checked once per month for proper voltage. Once every four (4) years the battery shall either be replaced or have a discharge test performed. The Seller shall maintain a log of these operations for inspection by the Company. d. Tests and battery replacements as specified in this Section 7 (Verification Testing) of Appendix B (Interconnection Requirements) shall be at the Seller’s expense.
Sample 1Sample 2Sample 3See All (8)
AutoNDA by SimpleDocs
Verification Testing. UL Contracting Party will perform periodic retesting of Client’s products it has assessed and found to comply with the energy efficiency requirements as previously outlined in the Quotation to verify their ongoing compliance. On an annual basis, the review may include UL Contracting Party’s retesting of at least 5%, or as specified in the Program specific requirements, of Client’s models representing Client’s product(s) previously found to comply with the energy efficiency requirements by procuring those such products from customary retail distribution channels, or as specified in the Program specific requirements. The acquisition and testing of such samples will be at Client’s expense. UL Contracting Party reserves the right to revoke use of the UL Mark on products and remove listing from the UL Contracting Party’s Product Database if UL Contracting Party determines the product is not in compliance with the requirements as outlined on the Quotation covering the UL Contracting Party’s Service preformed. If Client makes changes to the product(s) that will take the product(s) out of compliance with the requirements outlined on the Quotation, Client must promptly notify UL Contracting Party and submit the product for a re-assessment. If changes are made that take the product out of compliance and UL Contracting Party is not notified, Client may be required to suspend use of the UL Mark, report and/or certificate and pay a penalty when these changes are discovered during the annual verification testing. Continued noncompliance of the product may result in complete withdrawal from the EEC Services program.
Sample 1Sample 2
Verification Testing. 3.3.2.3.1 The Contractor shall support verification and validation testing of new systems and modifications to existing systems IAW plans and procedures including, but not limited to, factory acceptance testing, equipment receipt, system and modification integration, system and modification installation, System Operations Verification Testing (SOVT), and customer acceptance. 3.3.2.3.2 The Contractor shall assist with verifying and validating that hardware and software meet and are traceable to the requirements and verifying that the system and modification integration and installation were completed IAW the system solution documentation.‌
Sample 1
Verification Testing. Consultant shall oversee all testing of component materials and completed work items to the extent that it assures that the materials and workmanship incorporated in the Project are in conformity with the plans, specifications, and construction contract provisions.
Sample 1
Verification Testing. For all Products or its parts specification, Manufacturer shall draft appropriate verification protocol and perform the testing in accordance with that protocol. IWT shall author the system verification protocol and IWT shall accomplish verification and validation of the Product (“Verification Testing”). Third party (independent qualified testing facility) testing, in addition to related test materials, as shall be approved in advance by IWT, shall be paid by IWT, and shall be an agent of IWT. Test materials shall be the exclusive property of IWT. IWT will collect and/or prepare for Manufacturer data including vibration, shock, temperature, etc. of the actual environment where the product will be used. IWT will also perform operation verification during and at the end of development, operation verification on the actual test drive (field test), life and durability test, and the final acceptance tests.
Sample 1
Verification Testing. UL Solutions Contracting Party will perform periodic retesting of Client’s products it has assessed and found to comply with the energy efficiency requirements as previously outlined in the Quotation to verify their ongoing compliance. On an annual basis, the review may include UL Solutions Contracting Party’s retesting of at least 5%, or as specified in the Program specific requirements, of Client’s models representing Client’s product(s) previously found to comply with the energy efficiency requirements by procuring those such products from customary retail distribution channels, or as specified in the Program specific requirements. The acquisition and testing of such samples will be at Client’s expense. UL Solutions Contracting Party reserves the right to revoke use of the UL Mark on products and remove listing from the UL Solutions Contracting Party’s
Sample 1
Verification Testing. The Contractor shall conduct verification testing of all bugs/tasks, via the CXXI issue tracking tool. Tier-1 testing shall include all appropriate unclassified general scenarios and shall include specific functional scenarios. Tier-2 testing shall include classified production/study base case scenarios that are provided by the integrator/study teams. Verification testing shall be initiated in a timely manner (i.e., within 48 hours after notification during normal duty hours) after the bugs/tasks issues are completely resolved. Part of the verification process shall be proper documentation of the procedures used to resolve all issues.
Sample 1
AutoNDA by SimpleDocs
Verification Testing. The Grantor shall perform a verification test on the Products and Other Products manufactured in accordance with the Technology. If the verification test indicates that the manufacture of the Products or Other Products is in conformity with the technical specifications of the Technology, the verification test shall be considered to have been successfully completed. In the event that the verification is not successfully completed, the Grantor shall analyze the causes and take the necessary measures to eliminate the defects.
Sample 1
Verification Testing. Licensee must verify each Licensed Hard Core Implementation developed by Licensee pursuant to the license described in Section 2.1 or 2.3 of the Master Agreement on each process to be used for volume manufacture. For each such Licensed Hard Core Implementation developed pursuant to the rights granted in Section 2.1, Licensee shall run the latest architecture verification program (“AVP” or “Architecture Verification Program”) provided by MIPS under the applicable Technology Schedule, without any modification to the AVP, in accordance with the process set forth in either Section 2 or in Section 3 of this Exhibit B. For each such Licensed Hard Core Implementation developed pursuant to the rights granted in Section 2.3, Licensee shall run the latest verification test suite (“VTS” or “Verification Test Suite”) provided by MIPS under the applicable Technology Schedule, without any modification to the VTS, in accordance with the process set forth in either Section 2 or in Section 3 of this Exhibit B.
Sample 1

Related to Verification Testing

  • Inspection/Testing In order to assess Supplier’s work quality and/or compliance with this Order, upon reasonable notice by Buyer: (a) all goods, materials and services related to the items purchased hereunder, including, raw materials, components, assemblies, work in process, tools and end products shall be subject to inspection and testing by Buyer, its customer, representative or regulatory authorities at all places, including sites where the goods are made or located or the services are performed, whether at Supplier’s premises or elsewhere; and (b) all of Supplier’s facilities, books and records relating to this Order shall be subject to inspection by Buyer or its designee. If specific Buyer and/or Buyer’s customer tests, inspection and/or witness points are included in this Order, the goods shall not be shipped without an inspector’s release or a written waiver of test/inspection/witness with respect to each such point; however, Buyer shall not be permitted to unreasonably delay shipment; and Supplier shall notify Buyer in writing at least twenty (20) days prior to each of Supplier’s scheduled final and, if applicable, intermediate test/inspection/witness points. Supplier agrees to cooperate with such/audit inspection including, completing and returning questionnaires and making available its knowledgeable representatives. Buyer’s failure to inspect or test goods, materials or services or Buyer’s failure to reject or detect defects by inspection or testing shall not relieve Supplier from its warranty obligations or any of its other obligations or responsibilities under this Order. Supplier agrees to provide small business as well as minority and/or women owned business utilization and demographic data upon request.

  • ODUF Testing 6.6.1 Upon request from TWTC, AT&T shall send ODUF test files to TWTC. The Parties agree to review and discuss the ODUF file content and/or format. For testing of usage results, AT&T shall request that TWTC set up a production (live) file. The live test may consist of TWTC’s employees making test calls for the types of services TWTC requests on ODUF. These test calls are logged by TWTC, and the logs are provided to AT&T. These logs will be used to verify the files. Testing will be completed within thirty (30) days from the date on which the initial test file was sent.

  • Random Testing Notwithstanding any provisions of the Collective Agreement or any special agreements appended thereto, section 4.6 of the Canadian Model will not be applied by agreement. If applied to a worker dispatched by the Union, it will be applied or deemed to be applied unilaterally by the Employer. The Union retains the right to grieve the legality of any imposition of random testing in accordance with the Grievance Procedure set out in this Collective Agreement.

  • E-Verification The Vendor represents and warrants that it will ensure its compliance with the Mississippi Employment Protection Act of 2008, and will register and participate in the status verification system for all newly hired employees. Mississippi Code Annotated §§71-11-1 et seq. The term “employee” as used herein means any person that is hired to perform work within the State of Mississippi. As used herein, “status verification system” means the Illegal Immigration Reform and Immigration Responsibility Act of 1996 that is operated by the United States Department of Homeland Security, also known as the E-Verify Program, or any other successor electronic verification system replacing the E-Verify Program. Vendor agrees to maintain records of such compliance. Upon request of the State and after approval of the Social Security Administration or Department of Homeland Security when required, Vendor agrees to provide a copy of each such verification. Vendor further represents and warrants that any person assigned to perform services hereafter meets the employment eligibility requirements of all immigration laws. The breach of this agreement may subject Vendor to the following: termination of this contract for goods or services and ineligibility for any state or public contract in Mississippi for up to three (3) years with notice of such cancellation/termination being made public; the loss of any license, permit, certification, or other document granted to Vendor by an agency, department or governmental entity for the right to do business in Mississippi for up to one (1) year; or,

  • Test The outer surface of the lamp lenses shall be subjected once or more than once to the action of the sand jet produced as described above. The jet shall be sprayed almost perpendicular to the surface to be tested. The deterioration shall be checked by means of one or more samples of glass placed as a reference near the lenses to be tested. The mixture shall be sprayed until the variation in the diffusion of light on the sample or samples measured by the method described in Appendix 2, is such that: Δ d = (T5 - T4) / T2 ≤ 0.0250 ± 0.0025 Several reference samples may be used to check that the whole surface to be tested has deteriorated homogeneously.

  • MEASUREMENT AND VERIFICATION The goal of this task is to report the benefits resulting from this project by performing measurement and verification (M&V) of fossil fuel consumption and associated GHG reduction. • Enter into agreement with M&V subcontractor per Task 1.9 • Coordinate site visits with the M&V subcontractor at the demonstration site(s) • Develop M&V protocol for pre-installation measurements (and calculations): o Electric, natural gas and/or other fossil fuel consumption and GHG emissions (use appropriate emissions factor from Attachment 8 of the grant solicitation) of the equipment/process/system(s)/sub-system(s) that are to be upgraded and/or replaced and/or modified. o Ensure installation of sub-metering equipment and data loggers for pre/post data analysis. • Prepare and provide a detailed M&V Plan for each project demonstration site to include but not be limited to: o A description of the monitoring equipment and instrumentation which will be used. o A description of the key input parameters and output metrics which will be measured. o A description of the M&V protocol and analysis methods to be employed. o A description of the independent, third-party M&V services to be employed, if applicable. • Perform three months (or shorter period as approved in writing by the CAM) of pre- installation measurements (and calculations) based on the M&V protocol for pre- installation. • Prepare and provide a Pre-Installation M&V Findings Report for the demonstration site that includes M&V protocol, pre-install measurements (and calculations), analysis, and results performed in this task. • Develop M&V protocol for post-installation measurements (and calculations) of: o Electric, natural gas and/or other fossil fuel consumption and GHG emissions (use appropriate emissions factor from Attachment 8 of the grant solicitation) of the equipment/process/system(s)/sub-system(s) that will be upgraded and/or replaced and/or modified • Perform 12 months or two seasons, for seasonal facilities, (or shorter period as approved in writing by the CAM) of post-installation measurements based on M&V protocol for post-installation. • Provide a summary of post-installation M&V progress in Progress Report(s) (see subtask 1.5) which shall include but not be limited to:

  • Verification Bank may, from time to time, verify directly with the respective Account Debtors the validity, amount and other matters relating to the Accounts, either in the name of Borrower or Bank or such other name as Bank may choose.

  • Testing Landlord shall have the right to conduct annual tests of the Premises to determine whether any contamination of the Premises or the Project has occurred as a result of Tenant’s use. Tenant shall be required to pay the cost of such annual test of the Premises; provided, however, that if Tenant conducts its own tests of the Premises using third party contractors and test procedures acceptable to Landlord which tests are certified to Landlord, Landlord shall accept such tests in lieu of the annual tests to be paid for by Tenant. In addition, at any time, and from time to time, prior to the expiration or earlier termination of the Term, Landlord shall have the right to conduct appropriate tests of the Premises and the Project to determine if contamination has occurred as a result of Tenant’s use of the Premises. In connection with such testing, upon the request of Landlord, Tenant shall deliver to Landlord or its consultant such non-proprietary information concerning the use of Hazardous Materials in or about the Premises by Tenant or any Tenant Party. If contamination has occurred for which Tenant is liable under this Section 30, Tenant shall pay all costs to conduct such tests. If no such contamination is found, Landlord shall pay the costs of such tests (which shall not constitute an Operating Expense). Landlord shall provide Tenant with a copy of all third party, non-confidential reports and tests of the Premises made by or on behalf of Landlord during the Term without representation or warranty and subject to a confidentiality agreement. Tenant shall, at its sole cost and expense, promptly and satisfactorily remediate any environmental conditions identified by such testing in accordance with all Environmental Requirements. Landlord’s receipt of or satisfaction with any environmental assessment in no way waives any rights which Landlord may have against Tenant.

  • Compliance Verification (a) The sub recipient shall periodically interview a sufficient number of employees entitled to DB prevailing wages (covered employees) to verify that contractors or subcontractors are paying the appropriate wage rates. As provided in 29 CFR 5.6(a)(6), all interviews must be conducted in confidence. The sub recipient must use Standard Form 1445 (SF 1445) or equivalent documentation to memorialize the interviews. Copies of the SF 1445 are available from EPA on request. (b) The sub recipient shall establish and follow an interview schedule based on its assessment of the risks of noncompliance with DB posed by contractors or subcontractors and the duration of the contract or subcontract. Sub recipients must conduct more frequent interviews if the initial interviews or other information indicated that there is a risk that the contractor or subcontractor is not complying with DB. Sub recipients shall immediately conduct interviews in response to an alleged violation of the prevailing wage requirements. All interviews shall be conducted in confidence." (c) The sub recipient shall periodically conduct spot checks of a representative sample of weekly payroll data to verify that contractors or subcontractors are paying the appropriate wage rates. The sub recipient shall establish and follow a spot check schedule based on its assessment of the risks of noncompliance with DB posed by contractors or subcontractors and the duration of the contract or subcontract. At a minimum, if practicable, the sub recipient should spot check payroll data within two weeks of each contractor or subcontractor’s submission of its initial payroll data and two weeks prior to the completion date the contract or subcontract. Sub recipients must conduct more frequent spot checks if the initial spot check or other information indicates that there is a risk that the contractor or subcontractor is not complying with DB. In addition, during the examinations the sub recipient shall verify evidence of fringe benefit plans and payments there under by contractors and subcontractors who claim credit for fringe benefit contributions. (d) The sub recipient shall periodically review contractors and subcontractor’s use of apprentices and trainees to verify registration and certification with respect to apprenticeship and training programs approved by either the U.S Department of Labor or a state, as appropriate, and that contractors and subcontractors are not using disproportionate numbers of, laborers, trainees and apprentices. These reviews shall be conducted in accordance with the schedules for spot checks and interviews described in Item 5(b) and (c) above. • (e) Sub recipients must immediately report potential violations of the DB prevailing wage requirements to the EPA DB contact listed above and to the appropriate DOL Wage and Hour District Office listed at xxxx://xxx.xxx.xxx/whd/america2.htm. “Contractor shall comply with all applicable standards, orders, or requirements issued under section 306 of the Clean Air Act (42 U.S.C. 1857(h)), section 508 of the Clean Water Act (33 • U.S.C. 1368), Executive Order 11738, and Environmental Protection Agency regulations (40 CFR part 15). (Awards to Contractors and Subcontractors in Excess of $100,000) The undersigned certifies, to the best of his or her knowledge and belief, that: (1) No Federal appropriated funds have been paid or will be paid, by or on behalf of the undersigned, to any person for influencing or attempting to influence an officer or employee of any agency, a Member of Congress, an officer or employee of Congress, or an employee of a Member of Congress in connection with the awarding of any Federal contract, the making of any Federal grant, the making of any Federal loan, the entering into of any cooperative agreement, and the extension, continuation, renewal, amendment, or modification of any Federal contract, grant, loan or cooperative agreement. (2) If any funds other than Federal appropriated funds have been paid or will be paid to any person for influencing or attempting to influence an officer or employee of any agency, a Member of Congress, an officer or employee of Congress, or an employee of a Member of Congress in connection with this Federal contract, grant, loan, or cooperative agreement, the undersigned shall complete and submit Standard Form-LLL, “Disclosure Form to Report Lobbying,” in accordance with its instructions. (3) The undersigned shall require that the language of this certification be included in the award documents for all subawards at all tiers (including subcontracts, subgrants, and contracts under grants, loans, and cooperative agreements) and that all subrecipients shall certify and disclose accordingly. This certification is a material representation of fact upon which reliance was placed when this transaction was made or entered into. Submission of this certification is a prerequisite for making or entering into this transaction imposed by section 1352, title 31, U.S. Code. Any person who fails to file the required certification shall be subject to a civil penalty of not less than $10,000 and not more than $100,000 for each such failure. Title Date

  • Drug Testing (A) The state and the PBA agree to drug testing of employees in accordance with section 112.0455, F.S., the Drug-Free Workplace Act. (B) All classes covered by this Agreement are designated special risk classes for drug testing purposes. Special risk means employees who are required as a condition of employment to be certified under Chapter 633 or Chapter 943, F.S. (C) An employee shall have the right to grieve any disciplinary action taken under section 112.0455, the Drug-Free Workplace Act, subject to the limitations on the grievability of disciplinary actions in Article 10. If an employee is not disciplined but is denied a demotion, reassignment, or promotion as a result of a positive confirmed drug test, the employee shall have the right to grieve such action in accordance with Article 6.

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!