Installation Instructions. 7.1.5.2.1. Assembly instructions of all components together with diagrams or photographs showing clearly the layout of the single components w ithin the engine compartment.
7.1.5.2.2. Diagram or photograph showing the exact position where the installer shall place the retrofit system type approval plate (contained in the conversion kit).
7.1.5.2.3. Clear wiring diagram of the electrical system containing the mechanical components to which the wires shall be connected."
Installation Instructions. 1. Manufacturers installation instructions shall be standard catalogs or installation sheets furnished by the manufacturer modified as necessary to meet specific job conditions.
2. Instructions shall be of sufficient detail to indicate proper procedures to be used to comply with contract drawings.
3. Installation instructions shall be transmitted to the Architect for his information.
Installation Instructions. Producing appropriate and documented installation guidelines to the host sites which will, in case of unforeseen problems, allow the staff, in a reasonable time scale, to regress to the previous release.
Installation Instructions. The Supplier shall install the product in accordance with the “Installation Instructions” as provided by the equipment manufacturer. Any deviation from the “Installation Instructions” must have the prior written authorization from Siemens or the equipment manufacturer in order to prevent the adulteration of the finished medical device or creation of non-conformity to the devices performance specifications.
Installation Instructions. This manual is a supplement to the Xxxx Network Controller Instructions/Quick Start Guide, and the Access Anywhere Networking Manual which provide additional information on how to install the system on a customer’s LAN/WAN.
1. An automatic backup system is recommended so that all the MS Access files are backed up regularly. Note: All MS Access files must be shut down for a backup to take place.
2. A FULL version of MS Access must be installed on all workstations using the Custom Install procedure, and selecting ALL of the optional features of Access. Otherwise, the software may not function properly. There are two data formats of MS Access, Access 97, and Access 2000. (Access 2000 includes newer versions such as 2003, etc.) The newer versions of Xxxx software includes both formats. Older versions have only the 97
Installation Instructions. Provide manufacturer's written installation and adjustment instructions for finish hardware. Send installation instructions to site with hardware.
Installation Instructions. The installation of FundRaiser Professional is relatively simple and straightforward; simply put the CD in your CD drive, wait for the installation program to start up, then follow the prompts, accepting the default entries by clicking on the NEXT button. Or follow these steps:
Installation Instructions. If requested by Customer, Vendor will package with the Equipment all manufacturer and Customer supplied installation instructions.
Installation Instructions. To gain access, the inner fender panel needs to be removed. A flat bladed screwdriver can be used to pry up the heads of the plastic fasteners.
Installation Instructions. Run Setup. The setup is named SetupCutterDriverxx.EXE on the supplied CD. A shortcut to the installation instructions will be placed on the desktop. (DirectCut Help File). Documentation for the printer driver is included in the help file. Optional SmartMarkTM Sensor The SmartMarkTM option that is available for Xxxxx i-TECH cutters is an optical registration system that allows cutting of pre-printed graphics. The SmatMark system has the capability of recognizing up to three registration marks, and adjusting for scale and skew discrepancies the may occur. The SmartMarkTM option consists of an amplifier that is mounted to the cutting head, two fiber op- tic transmit/receive leads that connect to the amplifier, a lens assembly that is attached to the tool block assembly of the cutting head, and associated internal cutter wiring. The SmartMarkTM sensor recognizes changes in contrast from the background media to the printed mark. The “sensitivity” of the sensor must be set in order for the system to recognize the contrast reliably and be able to cut accurately. LABEL The recommended target is available for Adobe Illustrator and CorelDraw for download on the technical support page of the Xxxxx Datagraph web site (xxxx://xxx.xxxxxxxxxxxxxx.xxx). When designing a target for scanning, read the Title: Why thick lines don’t work Website Copy / CD Copy. The recommended Mark Size is 0.5 inch (12.7mm) the size can be as small as 0.25 inch (6.35 mm) or as large as 1 inch (25.4mm) The recommended line size is 0.13 (3.3mm) and can be as small as 0.07 inch (1.8mm). The registration mark should be printed with as high a contrast as possible. The sensor relies on reading the change in intensity of the reflection of the red LED pointer. When printing process colors on white media the best color is usually black. Certain spot colors are difficult. For example silver spot on white, while to the eye there is contrast the reflec- tivity of the two is sometimes nearly the same. Different medias also have different reflectivity and will on occasion require adjusting the sensor sensitivity (see below). If there is trouble with certain materials detecting the target you can print the target in a yellow or white field. The size of the yellow field should be double the scan distance. (Note: in order to get an accurate scan no other printed marks may appear in the yellow scan area. The printer color alignment marks can appear on the inside edge of the target or the other side of the medi...