Quality Control Requirements. To the extent this Agreement requires Contractor to provide processed food products, all food products shall be processed in a plant with well documented comprehensive in-house quality control and HACCP Programs that are third party certified as set forth in more detail below. The District reserves the right to determine whether or not the Contractor has complied with these product specifications in its sole discretion. If the District determines that the Contractor has provided a good and/or service that does not comply with these specifications, the District may 1) refuse to accept the good and/or service at no cost to the District, 2) require goods that have already been delivered and accepted by the District to be replaced at Contractor’s expense, 3) require services that have already been performed in a manner that does not comply with Agreement to be corrected at Contractor’s expense, 4) require the Contractor to reimburse the District for the cost of the nonconforming goods and/or services, 5) order replacement goods (if Contractor cannot timely provide conforming replacement goods) and order replacement goods from another vendor and charge Contractor the difference between the price listed in Schedule A and the amount the District had to pay the other vendor for the substitute goods, 6) declare Contractor in breach of this Agreement, 7) suspend the performance of this Agreement until the breach is cured and/or 8) terminate this Agreement for cause.
Quality Control Requirements. Each Party acknowledges the other Party’s exclusive ownership of the other Party’s Trademarks and that use by either Party or its Affiliates of any of the other Party’s Trademarks, including any resulting goodwill, will inure to the sole benefit of the Party that owns such Trademarks. Neither Party will knowingly do or permit to be done, and will cause its Affiliates not to do or cause to be done, any act or thing inconsistent with such ownership and will not acquire or claim or assist third parties in acquiring or claiming any title in or to any of the other Party’s Trademarks, including by virtue of the Strategic Alliance Agreement, this OEM Agreement, or through either Party’s use of the other Party’s Trademarks. Neither Party will directly or indirectly, and will cause its Affiliates not to directly or indirectly, undertake any action that in any manner might question, contest, challenge, infringe or impair the validity, enforceability, scope of rights or title of the other Party in any of the other Party’s Trademarks at any time during the term of the Strategic Alliance Agreement. Each Party agrees that (a) all Combined Offerings identified by any of the other Party’s Trademarks will be at least equal in quality to the mutually agreed specifications therefore (the “Quality Standard”) and (b) it will maintain, and will cause its Affiliates maintain, procedures to assure the consistent quality of all Combined Offerings bearing or containing the other Party’s Trademarks. Each Party will have the right to audit and inspect, upon advance written notice, at the inspecting Party’s sole expense, and during regular business hours, the use by the other Party and its Affiliates of its Trademarks licensed hereunder and all Combined Offerings identified by any of its Trademarks (f)
Quality Control Requirements. In furtherance of the foregoing, any use by any of the Parties or any of their Subsidiaries or Affiliates of any of the Tyco Trademarks or Other Party Marks as permitted in this Section 5.2 is subject to their compliance with the quality control requirements and guidelines in effect for the Other Party Marks as of the Effective Time
Quality Control Requirements. Contractor shall maintain a viable Quality Control Program that ensures that the paint supplied conforms to the Contract specifications. At a minimum, the program must include: (a) Routine verification of the type, quality, and purity of raw materials; (b) Sampling, testing, and record keeping on all batches produced; (c) A procedure for valve and tote checks for all reusable totes that are repurposed; and (d) A procedure to administer flow checks prior to shipping totes with valves to ensure no air bubbles or clogged totes. Quality control test run on each batch shall be sufficient to ensure that the paint meets specifications. All paint batches shall have a unique number assigned to them, which shall be used to correlate control test results and identify individual containers. Contractor shall allow Enterprise Services full access to all quality control process and records pertaining to the paints procured for this Contract.
Quality Control Requirements. In keeping with OCD Quality Assurance and Control Requirements and the provisions of ISO 13485, SNBTS shall comply with all of the provisions of the Quality System Agreement between SNBTS and OCD. In the event of a conflict in terms between this Umbrella Agreement and the Quality System Agreement, the Umbrella Agreement shall control.
Quality Control Requirements. Quality Control Requirements shall mean that JULPHAR shall subject all Active Ingredient to quality control inspections using quality control procedures, specifications, and systems to assure strict compliance with the Specifications and absence of defects.
Quality Control Requirements. Identify and discuss the procedures that will be used to review, modify, and approve plan documents and associated permits. Include methods and procedures to control, document, and accept the quality of the design activities listed in Section IV of the Special Provision titled SPECIAL BIDDING – DESIGN- BUILD. Include the following quality control items as a minimum:
Quality Control Requirements. The Contractor’s and subcontractor’s Quality Control Plans (QCPs) are subject to the acceptance by the Employer. The Contractor ensures that all specifications and requirements are communicated to the relevant parties in his organisation and does not deviate from it. All Contractor’s QCPs are accepted by the Project Manager, the Contractor and the Employer’s Appointed Inspection Authority / QA representative (as applicable) prior to the commencement of work. Only after acceptance of these documents by the Project Manager and the Employer’s QA representative / AIA as applicable, may the work proceed. The Contractor ensures that all work (Contractor and subcontractor work) is carried out in accordance with the QCPs or any other specifications through written instructions from the Project Manager. All documentation has a clearly stated revision number and previous similar documentation is revoked. All quality related problems / issues are reported and resolved as Defects in terms of Core Clause 42.2. Refer to the TRSs specifying the grades of non-conformances. All completed work is signed off in the QCPs as the work progress and all the relevant signatures are made on the documentation. The Contractor and his subcontractor employ quality control representatives, with appropriate proven experience.
Quality Control Requirements. The Contractor’s and subcontractor’s quality control programmes are subject to the acceptance by the Supervisor. The Contractor ensures that all specifications and requirements are communicated to the relevant parties in his organisation and does not deviate from it. All Contractor’s Quality Control Plans (QCPs) are accepted by the Supervisor and the Contractor prior to the commencement of work. Only after acceptance of these documents by the Project Manager, may the work proceed. The Contractor ensures that all work (Contractor and subcontractor work) is carried out in accordance with the QCPs or any other specifications through written instructions from the Supervisor. All documentation has a clearly stated revision number and previous similar documentation is revoked. All quality related problems/issues are reported and resolved as Defects in terms of Core Clause 42.2. All completed work is signed off in the QCPs as the work progresses and all the relevant signatures are made on the documentation. The Contractor and his subcontractor employs quality control representatives, with appropriate proven experience.
Quality Control Requirements. 26 22. CONFLICT RESOLUTION - MEDIATION............................... 32 23. MISCELLANEOUS................................................. 33 MASTER DEVELOPMENT AND TOLL MANUFACTURING AGREEMENT ------------------------------------------------------------------ THIS AGREEMENT is made as of this 3rd day of May 2001 by and between Novartis Consumer Health, Inc., 560 Morris Avenue, Summit, NJ 07901 and Endo Pharmaceuticals Inc., 000 Xxxxxxxxxx Xxxx Chester Pike, Chadds Ford, PA 19317. XXXXXXXXXX
