Measurement Equipment and Procedures Sample Clauses

Measurement Equipment and Procedures. 8.1 All Gas measurements required hereunder shall be made with equipment of standard make to be furnished, installed, operated, and maintained by MarkWest in accordance with the recommendations contained in ANSI/API 2530 as then published. Producer, or others having Producer’s consent, may, at its option and expense, install and operate check measuring equipment upstream of the measuring equipment to check the measuring equipment, provided the installation of the check measuring equipment in no way interferes with the operation of the measuring equipment. 8.2 All Gas volume measurements shall be based on an assumed atmospheric pressure of 14.4 psia, regardless of actual atmospheric pressure at which the Gas is measured. The factors used in computing Gas volumes from orifice meter measurements shall be the latest factors published by the AGA. These factors shall include: a. Basic orifice factor. b. Pressure base factor based on a pressure base of 14.73 psia. c. Temperature base factor based on a temperature base of sixty degrees Fahrenheit (60°F). d. Flowing temperature factor, based on the flowing temperature as measured by an industry accepted recording device, if, at MarkWest’s option, a recording device has been installed, otherwise the temperature shall be assumed to be sixty degrees Fahrenheit (60°F). e. Super compressibility factor, obtained from the latest AGA Manual for the Determination of Super Compressibility Factors for Natural Gas (AGA 8). f. Specific gravity factor, based on the specific gravity of the Gas as determined under the provisions set forth below. 8.3 MarkWest shall test the accuracy of its measuring equipment at least once every calendar quarter. Additional test(s) shall be promptly performed upon notification by either Party to the other. If any additional test requested by Producer indicates that no inaccuracy of more than two percent (2%) exists, at a recording rate corresponding to the average rate of flow for the period since the last preceding test, then Producer shall reimburse MarkWest for all its direct costs in connection with that additional test within fifteen (15) days following receipt of a detailed invoice and supporting documentation setting forth those costs. 8.4 If, upon test, any measuring equipment is found to be in error by an amount not exceeding two percent (2%), at a recording rate corresponding to the average rate of flow for the period since the last preceding test, previous recordings of that equipment sh...
AutoNDA by SimpleDocs
Measurement Equipment and Procedures. 5.1. All Gas measurements required hereunder shall be made with equipment furnished, installed, operated, and maintained by Columbia in accordance with Columbia's Gas Tariff and applicable standards of the American Gas Association, and the provisions of the applicable Operating Agreements.
Measurement Equipment and Procedures. 6.1. The volume of Gas will be measured by a primary and secondary measurement device that is accepted by industry, state, and federal regulatory agencies. The most common primary devices are orifice or ultrasonic meter tubes. These devices shall comply with the American Petroleum Institute - Manual of Petroleum Measurement Standards, 14.3, American Gas Association Report No. 3, and Report No. 9, (Latest Revisions) where applicable. The secondary measurement device shall be an electronic flow meter (“EFM”) that includes a temperature recording system. The EFM shall meet and be capable of performing volume calculations according to the current standards prescribed in the American Gas Association Report No. 3, Orifice Metering of Natural Gas and Other Hydrocarbon Fluids, Parts 1-4, and shall comply with the American Petroleum Institute — Manual of Petroleum Measurement Standards, Chapter 21, Section 1 — Electronic Gas Measurement, (Latest Revisions). 6.2. The unit of volume for measurement of Gas delivered hereunder shall be one thousand (1,000) Cubic feet of Gas at a base temperature of sixty degrees Fahrenheit (60°F) and at an absolute pressure base of 14.73 psia. 6.3. For purposes of measurement hereunder, the atmospheric (barometric) pressure shall be the average actual atmospheric pressure for the geographical area as determined by the Processor. If the pressure transmitter being used is capable of measuring actual atmospheric pressure, then actual atmospheric pressure may be used. 6.4. Processor shall determine the Gas stream composition, specific gravity, and gross Heating Values based on any of the following: spot samples, composite samples, on-line Gas chromatograph analysis or portable Gas chromatograph analysis. The component analysis of the Gas shall be performed by Gas chromatography in accordance with GPA 2261 and 2172 or any pertinent revisions thereto or replacements thereof. Gas samples shall be obtained in accordance with the procedures set forth in the Gas Processor’s Association Standard 2166 (Latest Revision) “Obtaining Natural Gas Samples for Analysis by Gas Chromatography” and American Petroleum Institute 14.1 Section 1 (Latest Revision). 6.5. The sampling frequency will be no less than semi-annually or more often if deemed necessary by Processor. 6.6. Tests for oxygen, carbon dioxide, sulphur, and hydrogen sulfide content of the Gas delivered hereunder shall be made as often as deemed necessary by Processor, by means commonly used and...
Measurement Equipment and Procedures. All Gas measurements required hereunder shall be made with equipment of standard make to be furnished, installed, operated, and maintained by Processor in accordance with the recommendations set forth in the A.G.A. Gas Measurement Committee Report Number Three-latest edition for orifice meters or the A.G.A. Gas Measurement Committee Report Number Seven-latest edition for turbine meters or industry standards for other meters. Chipeta may, at its option and expense, install and operate check measuring equipment upstream of the measuring equipment to check the measuring equipment, provided that the installation of the check measuring equipment in no way interferes with the operation of the measuring equipment.
Measurement Equipment and Procedures. 8.1. All Gas measurements required hereunder shall be made with equipment of standard make to be furnished, installed, operated, and maintained by Keystone in accordance with the recommendations contained in ANSI/API 2530 as then published. Xxx, or others having Rex’s consent, may, at its option and expense, install and operate check measuring equipment Upstream of the measuring equipment to check the measuring equipment, provided the installation of the check measuring equipment in no way interferes with the operation of the measuring equipment.
Measurement Equipment and Procedures. 6.1. All Gas measurements required hereunder shall be made with equipment of standard make to be furnished, installed, operated, and maintained by Processor in accordance with the recommendations set forth in the A.G.A. Gas Measurement Committee Report Number Three-latest edition for orifice meters or the A.G.A. Gas Measurement Committee Report Number Seven-latest edition for turbine meters or industry standards for other meters. Producer may, at its option and expense, install and operate check measuring equipment upstream of the measuring equipment to check the measuring equipment, provided that the installation of the check measuring equipment in no way interferes with the operation of the measuring equipment. 6.2. All Gas volume measurements shall be based on an assumed atmospheric pressure of 11.7 psia, regardless of actual atmospheric pressure at which the Gas is measured. The factors used in computing Gas volumes from orifice meter measurements shall be the latest factors
Measurement Equipment and Procedures 
AutoNDA by SimpleDocs

Related to Measurement Equipment and Procedures

  • Notice and Procedures If any suit, action, proceeding (including any governmental or regulatory investigation), claim or demand shall be brought or asserted against any person in respect of which indemnification may be sought pursuant to either paragraph (a) or (b) above, such person (the “Indemnified Person”) shall promptly notify the person against whom such indemnification may be sought (the “Indemnifying Person”) in writing; provided that the failure to notify the Indemnifying Person shall not relieve it from any liability that it may have under paragraph (a) or (b) above except to the extent that it has been materially prejudiced (through the forfeiture of substantive rights or defenses) by such failure; and provided, further, that the failure to notify the Indemnifying Person shall not relieve it from any liability that it may have to an Indemnified Person otherwise than under paragraph (a) or (b) above. If any such proceeding shall be brought or asserted against an Indemnified Person and it shall have notified the Indemnifying Person thereof, the Indemnifying Person shall retain counsel reasonably satisfactory to the Indemnified Person (who shall not, without the consent of the Indemnified Person, be counsel to the Indemnifying Person) to represent the Indemnified Person in such proceeding and shall pay the fees and expenses of such counsel related to such proceeding, as incurred. In any such proceeding, any Indemnified Person shall have the right to retain its own counsel, but the fees and expenses of such counsel shall be at the expense of such Indemnified Person unless (i) the Indemnifying Person and the Indemnified Person shall have mutually agreed to the contrary; (ii) the Indemnifying Person has failed within a reasonable time to retain counsel reasonably satisfactory to the Indemnified Person; (iii) the Indemnified Person shall have reasonably concluded that there may be legal defenses available to it that are different from or in addition to those available to the Indemnifying Person; or (iv) the named parties in any such proceeding (including any impleaded parties) include both the Indemnifying Person and the Indemnified Person and representation of both parties by the same counsel would be inappropriate due to actual or potential differing interest between them. It is understood and agreed that the Indemnifying Person shall not, in connection with any proceeding or related proceedings in the same jurisdiction, be liable for the fees and expenses of more than one separate firm (in addition to any local counsel) for all Indemnified Persons, and that all such fees and expenses shall be paid or reimbursed as they are incurred. Any such separate firm for any Underwriter, its affiliates, directors and officers and any control persons of such Underwriter shall be designated in writing by the Representatives and any such separate firm for the Company, its directors, its officers who signed the Registration Statement and any control persons of the Company shall be designated in writing by the Company. The Indemnifying Person shall not be liable for any settlement of any proceeding effected without its written consent, but if settled with such consent or if there be a final judgment for the plaintiff, the Indemnifying Person agrees to indemnify each Indemnified Person from and against any loss or liability by reason of such settlement or judgment. Notwithstanding the foregoing sentence, if at any time an Indemnified Person shall have requested that an Indemnifying Person reimburse the Indemnified Person for fees and expenses of counsel as contemplated by this paragraph, the Indemnifying Person shall be liable for any settlement of any proceeding effected without its written consent if (i) such settlement is entered into more than 30 days after receipt by the Indemnifying Person of such request and (ii) the Indemnifying Person shall not have reimbursed the Indemnified Person in accordance with such request prior to the date of such settlement. No Indemnifying Person shall, without the written consent of the Indemnified Person, effect any settlement of any pending or threatened proceeding in respect of which any Indemnified Person is or could have been a party and indemnification could have been sought hereunder by such Indemnified Person, unless such settlement (x) includes an unconditional release of such Indemnified Person, in form and substance reasonably satisfactory to such Indemnified Person, from all liability on claims that are the subject matter of such proceeding and (y) does not include any statement as to or any admission of fault, culpability or a failure to act by or on behalf of any Indemnified Person.

  • Standard Operating Procedures Standard Operating Procedures shall not contravene the Canada Labour Code, the Canadian Human Rights Code, or the Collective Agreement, and an allegation of such contravention is subject to the grievance procedure.

  • Operational Procedures In order to minimize operational problems, it will be necessary for trade information to be supplied in a secure manner by the Subadviser to the Fund’s Service Providers, including: JPMorgan Chase Bank, National Association (the “Custodian”), Virtus Fund Services (the “Fund Administrator”) BNY Mellon Investment Servicing (US) Inc., (the “Sub-Accounting Agent”), any Prime Broker to the Series, and all other Counterparties/Brokers as required. The Subadviser must furnish the Fund’s service providers with required daily information as to executed trades in a format and time-frame agreed to by the Subadviser, Custodian, Fund Administrator, Sub-Accounting Agent and Prime Broker/Counterparties and designated persons of the Fund. Trade information sent to the Custodian, Fund Administrator, Sub-Accounting Agent and Prime Broker/Counterparties must include all necessary data within the required timeframes to allow such parties to perform their obligations to the Series. The Sub-Accounting Agent specifically requires a daily trade blotter with a summary of all trades, in addition to trade feeds, including, if no trades are executed, a report to that effect. Daily information as to executed trades for same-day settlement and future trades must be sent to the Sub-Accounting Agent no later than 4:30 p.m. (Eastern Time) on the day of the trade each day the Fund is open for business. All other executed trades must be delivered to the Sub-Accounting Agent on Trade Date plus 1 by Noon (Eastern Time) to ensure that they are part of the Series’ NAV calculation. (The Subadviser will be responsible for reimbursement to the Fund for any loss caused by the Subadviser’s failure to comply with the requirements of this Schedule A.) On fiscal quarter ends and calendar quarter ends, all trades must be delivered to the Sub-Accounting Agent by 4:30 p.m. (Eastern Time) for inclusion in the financial statements of the Series. The data to be sent to the Sub-Accounting Agent and/or Fund Administrator will be as agreed by the Subadviser, Fund Administrator, Sub-Accounting Agent and designated persons of the Fund and shall include (without limitation) the following:

  • Safeguarding requirements and procedures (1) The Contractor shall apply the following basic safeguarding requirements and procedures to protect covered contractor information systems. Requirements and procedures for basic safeguarding of covered contractor information systems shall include, at a minimum, the following security controls: (i) Limit information system access to authorized users, processes acting on behalf of authorized users, or devices (including other information systems). (ii) Limit information system access to the types of transactions and functions that authorized users are permitted to execute. (iii) Verify and control/limit connections to and use of external information systems. (iv) Control information posted or processed on publicly accessible information systems. (v) Identify information system users, processes acting on behalf of users, or devices. (vi) Authenticate (or verify) the identities of those users, processes, or devices, as a prerequisite to allowing access to organizational information systems. (vii) Sanitize or destroy information system media containing Federal Contract Information before disposal or release for reuse. (viii) Limit physical access to organizational information systems, equipment, and the respective operating environments to authorized individuals. (ix) Escort visitors and monitor visitor activity; maintain audit logs of physical access; and control and manage physical access devices. (x) Monitor, control, and protect organizational communications (i.e., information transmitted or received by organizational information systems) at the external boundaries and key internal boundaries of the information systems. (xi) Implement subnetworks for publicly accessible system components that are physically or logically separated from internal networks. (xii) Identify, report, and correct information and information system flaws in a timely manner. (xiii) Provide protection from malicious code at appropriate locations within organizational information systems. (xiv) Update malicious code protection mechanisms when new releases are available. (xv) Perform periodic scans of the information system and real-time scans of files from external sources as files are downloaded, opened, or executed.

  • Interconnection Facilities Engineering Procurement and Construction Interconnection Facilities, Network Upgrades, and Distribution Upgrades shall be studied, designed, and constructed pursuant to Good Utility Practice. Such studies, design and construction shall be based on the assumed accuracy and completeness of all technical information received by the Participating TO and the CAISO from the Interconnection Customer associated with interconnecting the Large Generating Facility.

  • Policies and Procedures i) The policies and procedures of the designated employer apply to the employee while working at both sites. ii) Only the designated employer shall have exclusive authority over the employee in regard to discipline, reporting to the College of Nurses of Ontario and/or investigations of family/resident complaints. iii) The designated employer will ensure that the employee is covered by WSIB at all times, regardless of worksite, while in the employ of either home. iv) The designated employer will ensure that the employee is covered by liability insurance at all times, regardless of worksite, while in the employ of either home. v) The designated employer shall have exclusive authority over the employee’s personnel files and health records. These files will be maintained on the site of the designated employer.

  • Additional Procedures (i) Once initiated by an Auction Notice, the Auction Party may not withdraw an Auction other than a Failed Auction. Furthermore, in connection with any Auction, upon submission by a Lender of a Qualifying Bid, such Lender (each, a “Qualifying Lender”) will be obligated to sell the entirety or its allocable portion of the Reply Amount, as the case may be, at the Applicable Price. (ii) To the extent not expressly provided for herein, each purchase of Term Loans pursuant to an Auction shall be consummated pursuant to procedures consistent with the provisions in this definition, established by the Auction Agent acting in its reasonable discretion and as reasonably agreed by the Borrower. (iii) In connection with any Auction, the Borrower and the Lenders acknowledge and agree that the Auction Agent may require as a condition to any Auction, the payment of customary fees and expenses by the Auction Party in connection therewith as agreed between the Auction Party and the Auction Agent. (iv) Notwithstanding anything in any Loan Document to the contrary, for purposes of this definition, each notice or other communication required to be delivered or otherwise provided to the Auction Agent (or its delegate) shall be deemed to have been given upon the Auction Agent’s (or its delegate’s) actual receipt during normal business hours of such notice or communication; provided that any notice or communication actually received outside of normal business hours shall be deemed to have been given as of the opening of business on the next Business Day. (v) The Borrower and the Lenders acknowledge and agree that the Auction Agent may perform any and all of its duties under this definition by itself or through any Affiliate of the Auction Agent and expressly consent to any such delegation of duties by the Auction Agent to such Affiliate and the performance of such delegated duties by such Affiliate. The exculpatory provisions pursuant to this Agreement shall apply to each Affiliate of the Auction Agent and its respective activities in connection with any purchase of Term Loans provided for in this definition as well as activities of the Auction Agent.

  • Testing Procedures Testing will be conducted by an outside certified Agency in such a way to ensure maximum accuracy and reliability by using the techniques, chain of custody procedures, equipment and laboratory facilities which have been approved by the U.S. Department of Health and Human Services. All employees notified of a positive controlled substance or alcohol test result may request an independent test of their split sample at the employee’s expense. If the test result is negative the Employer will reimburse the employee for the cost of the split sample test.

  • Equipment Specifications All equipment must meet the contract specifications and all federal and State safety codes and regulations in effect at the date of manufacture. All equipment must be Original Equipment Manufacturer (OEM) equipment unless otherwise stated in the contract. All products, materials, supplies, replacement parts, and equipment offered and furnished must be new, of current manufacturer production, and must have been formally announced by the manufacturer as being commercially available, unless otherwise stated in this Contract.

  • System Upgrade Facilities and System Deliverability Upgrades Connecting Transmission Owner shall design, procure, construct, install, and own the System Upgrade Facilities and System Deliverability Upgrades described in Appendix A hereto. The responsibility of the Developer for costs related to System Upgrade Facilities and System Deliverability Upgrades shall be determined in accordance with the provisions of Attachment S to the ISO OATT.

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!