Design Phase Basic Services Sample Clauses

Design Phase Basic Services. (a) Design Phase services provided by the PM pursuant to this PM Agreement shall include the administration of a Design Contract, a Design/Build Contract and/or a CM At-Risk Delivery Method Contract so that (i) the design results in a project that meets the User Agency and the City of Xxxxxxxx’x needs and conforms to the Study, the Designers Procedures Manual, the standards set forth in the Design Contract or Design/Build Agreement and such other guidelines and standards as may be stipulated by the City of Xxxxxxxx, and applicable Laws; (ii) all Permits are obtained on schedule by the Designer or Design/Build contractor; and (iii) that any contracts to be put out to bid are properly bid and reviewed and evaluated in accordance with applicable Laws. (b) Without limiting the foregoing, the PM shall: i. provide general project management services; ii. provide document review services; iii. provide prequalification review services; iv. provide detailed cost estimating services; v. provide value engineering services; vi. provide record keeping and reporting services; vii. provide scheduling and phasing services, design/build and construction bidding and planning services, and bid reviewing services. viii. in a timely manner make written recommendations to the Capital Assets Manager regarding Approvals and reasons for disapproval to be sent to the Designer under the Design Contract Designer; ix. coordinate the meetings of the Designer, the Capital Assets Manager or his representatives, the User Agency, and any other necessary parties, including, without limitation, DCAMM and other Commonwealth representatives; x. attend public meetings;
AutoNDA by SimpleDocs
Design Phase Basic Services. The CM shall review the following A-E Deliverables and provide its comments and recommendations to JWA within 21 days after receipt: A-E Milestone Dates A-E Deliverables (A-E Design Phase Basic Services) Parking Structure C Bid Package: March 11, 2008 Schematic Design May 21, 2008 Design Development A-E Milestone Dates A-E Deliverables (A-E Design Phase Basic Services) October 1, 2008 95% Construction Documents November 5, 2008 Construction Documents (Stamped and Reproducible Set) The CM shall also: 1) Deliver the following reports within 21 days after receipt of each of the above AE Deliverables: a) Deliver construction cost estimate (Schematic Design and Construction Documents milestones only). b) Deliver value analysis report. c) Deliver systems analysis report. d) Deliver constructability review report. e) Deliver long-lead items strategy report. f) Deliver labor, Contractor, subcontractor, and supplier interest report. g) Deliver safety risk analysis report. h) Deliver quality analysis report. i) Deliver project risk analysis report. j) Deliver site logistics report. k) Deliver permit report. 2) Deliver a Construction Management Plan within 30 calendar days following award of this Agreement. 3) Deliver design phase progress reports with the CM’s monthly invoice. 4) Deliver construction specifications for contractor quality control and safety 60 calendar days prior to the A-E’s 95% Construction Document deliverable milestone date.
Design Phase Basic Services. The CM shall review the following D-B Deliverables and provide its comments and recommendations to JWA within 21 days after receipt: Design Development 95% Construction Documents Construction Documents (Stamped and Reproducible Set) The CM shall also: 1) Deliver the following reports within 21 days after receipt of each of the above D-B Deliverables: a) a) Deliver value analysis report.
Design Phase Basic Services. The Design Phase Basic Services are included in: (a) This APPENDIX I: Scope of Services (b) Attachment A.1: Special Studies Scope Matrices (c) Attachment A.2: Geotechnical Scope of Services (d) Attachment A.3: Description of Deliverables (e) Attachment A.4: Basis of DesignMinimum Requirements (f) Attachment A.7: Detailed Civil Engineering Scope of Services

Related to Design Phase Basic Services

  • Design Phase All Basic Services set forth in the Agreement with the exception of Interdisciplinary Document Coordination Review, conducting a Card Trick session, Value-Engineering services, Estimating services. • All Basic Services set forth in the Agreement. • All Basic Services set forth in the Agreement. • All Basic Services set forth in the Agreement.

  • Construction Phase Services 3.1.1 – Basic Construction Services

  • Design Development Phase INDICATE IN STATEMENT OF WORK “NOT APPLICABLE” IF SECTION IS NOT APPLICABLE 1.1.6.1. The ARCHITECT/ENGINEER shall prepare from the approved Schematic Design Studies, the Design Development Documents consisting of drawings (including at least architectural, landscaping, civil, structural, mechanical and electrical plans, building sections; and finish schedule), outline specifications following the Construction Specification Institute "CSI" Format and other necessary documents to fix and describe the size and character of the entire Project as to its site, structural, mechanical, and electrical systems, materials and other such essentials as may be appropriate, for and until approved by the State. 1.1.6.2. The ARCHITECT/ENGINEER shall conduct meetings with the State, Efficiency Vermont, and relevant members of the design team, to review the Design Development Documents for the purposes of furthering the energy efficiency objectives of the Project. 1.1.6.3. The ARCHITECT/ENGINEER shall prepare for the State a revised accounting of how the Project is responding to LEED criteria. 1.1.6.4. The ARCHITECT/ENGINEER shall submit to the State a revised Statement of Probable Construction Cost based thereon for and until approved by the State.

  • Schematic Design Phase 1.2.1 Based on the mutually agreed upon Program of Requirements, Amount Available for the Construction Contract and the Project Schedule, the Architect/Engineer shall prepare sufficient alternative approaches utilizing BIM for design and construction of the Project to satisfy Owner’s project requirements and shall, at completion of this phase, submit Schematic Design Documents derived from the model in accordance with the BIM Execution Plan, “Facility Design Guidelines” and any additional requirements set forth in Article 15. The Architect/Engineer shall review alternative approaches to design and construction for the Project as they are being modeled at intervals appropriate to the progress of the Project with the Owner and Construction Manager at the Project site or other location specified by the Owner within the State of Texas. The Architect/Engineer shall utilize the model(s) to support the review process during Schematic Design. The Architect/Engineer shall provide the Construction Manager with a compact disc containing documents and data files derived from the model to assist the Construction Manager in fulfilling its responsibilities to the Owner. 1.2.2 Architect/Engineer shall provide all services necessary to perform the services of this phase (preparation of model(s), relevant data, decision support model views and Schematic Design Documents) including, without limitation, unless otherwise approved by Owner, the preparation and prompt delivery of all items specified in the BIM Execution Plan and “Facility Design Guidelines”. 1.2.3 Architect/Engineer shall work closely with Owner in preparation of schematic drawings and shall specifically conform to Owner’s requirements regarding aesthetic design issues. 1.2.4 The Architect/Engineer shall review the Estimated Construction Cost prepared by the Construction Manager, and shall provide written comments. 1.2.5 Before proceeding into the Design Development Phase, the Architect/Engineer shall obtain Owner’s written acceptance of the Schematic Design documents and approval of the Architect/Engineer’s preliminary Estimated Construction Cost and schedule. 1.2.6 The Architect/Engineer shall participate in a final review of the Schematic Design Documents and model(s) with the Owner and Construction Manager at the Project site or other location specified by Owner in the State of Texas. Prior to the Owner’s approval of the Schematic Design Documents, the Architect/Engineer shall incorporate such changes as are necessary to satisfy the Owner’s review comments, any of which may be appealed for good cause.

  • PRE-CONSTRUCTION PHASE SERVICES The Pre-Construction Phase shall be deemed to commence upon the date specified in a written Notice to Proceed with Pre-Construction Phase Services issued by Owner and shall continue through completion of the Construction Documents and procurement of all major Subcontractor agreements. Contractor is not entitled to reimbursement for any costs incurred for Pre-Construction Phase Services performed before issuance of the written Notice to Proceed. Pre-Construction Phase Services may overlap Construction Phase Services. Contractor shall perform the following Pre-Construction Phase Services:

  • Final Design Phase A. After acceptance by Owner of the Preliminary Design Phase documents, revised opinion of probable Construction Cost as determined in the Preliminary Design Phase, and/or any other Right of Way plan documents, subject to any Owner-directed modifications or changes in the scope, extent, character, or design requirements of or for the Project, and upon written authorization from Owner, Engineer shall: 1. Prepare final Drawings and Specifications indicating the scope, extent, and character of the Work to be performed and furnished by Contractor. 2. Visit the Site as needed to assist in preparing the final Drawings and Specifications. 3. Provide technical criteria, written descriptions, and design data for Owner’s use in filing applications for permits from or approvals of governmental authorities having jurisdiction to review or approve the final design; assist Owner in consultations with such authorities; and revise the Drawings and Specifications in response to directives from such authorities, as appropriate. 4. Advise Owner of any recommended adjustments to the opinion of probable Construction Cost. 5. After consultation with Owner, include in the Construction Contract Documents any specific protocols for the transmittal of Project-related correspondence, documents, text, data, drawings, information, and graphics, in electronic media or digital format, either directly, or through access to a secure Project website. Any such protocols shall be applicable to transmittals between and among Owner, Engineer, and Contractor during the Construction Phase and Post- Construction Phase, and unless agreed otherwise shall supersede any conflicting protocols previously established for transmittals between Owner and Engineer. 6. Assist Owner in assembling known reports and drawings of Site conditions, and in identifying the technical data contained in such reports and drawings upon which bidders or other prospective contractors may rely. 7. In addition to preparing the final Drawings and Specifications, assemble drafts of other Construction Contract Documents based on specific instructions and contract forms, text, or content received from Owner. 8. Prepare or assemble draft bidding-related documents (or requests for proposals or other construction procurement documents), based on the specific bidding or procurement-related instructions and forms, text, or content received from Owner. 9. Contract shall include contractor provided changeable message signs to communication construction information. 10. Furnish for review by Owner, its legal counsel, and other advisors, 6 copies of the final drawings and Specifications, assembled drafts of other construction Contract Documents, the draft bidding-related documents (or requests for proposals or other construction procurement documents), and any other final design Phase deliverables, by the established due date, with the Final Design Phase, and review them with Owner. Owner shall submit to Engineer any comments regarding the furnished items, and any instructions for revisions. B. Engineer’s services under the Final Design Phase will be considered complete on the date when Engineer has delivered to Owner the final Drawings and Specifications, other assembled Construction Contract Documents, bidding-related documents (or requests for proposals or other construction procurement documents), and any other Final Design Phase deliverables. C. In the event that the Work designed or specified by Engineer is to be performed or furnished under more than one prime contract, or if Engineer’s services are to be separately sequenced with the work of one or more prime Contractors (such as in the case of fast- tracking), Owner and Engineer shall, prior to commencement of the Final Design Phase, develop a schedule for performance of Engineer’s services during the Final Design, Bidding or Negotiating, Construction, and Post-Construction Phases in order to sequence and coordinate properly such services as are applicable to the work under such separate prime contracts.

  • Construction Phase Fee Contractor’s Construction Phase Fee is the maximum amount payable to Contractor for any cost or profit expectation incurred in the performance of the Work that is not specifically identified as being eligible for reimbursement by Owner elsewhere in this Agreement. References in the UGSC to Contractor’s “overhead” and “profit” mean Contractor’s Construction Phase Fee. The Construction Phase Fee includes, but is not limited to, the following items: 9.1 All profit, profit expectations and costs associated with profit sharing plans such as personnel bonuses, incentives, and rewards; company stock options; or any other like expenses of Contractor.

  • Construction Phase Part 1 –

  • PREVAILING WAGE RATES - PUBLIC WORKS AND BUILDING SERVICES CONTRACTS If any portion of work being Bid is subject to the prevailing wage rate provisions of the Labor Law, the following shall apply:

  • Pre-Commencement Phase Services The services required to be provided by the Contractor for the Pre- Commencement Phase of the Project in accordance with the Contract Documents.

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!